rode psa1 base 3d models

Replacement for the plastic part of the Rode PSA1 boom arm clamp

This is a clip made for fixing a FetHead microphone pre-amplifier to the Rode PSA1 boomarm. ... Made this to add some weight to the boomarm and to keep the setup neat.

You can see an example of a break similar to mine here: https://www.reddit.com/r/rode/comments/uwlxoe/psa1_base_broke/ I'd recommend buying some rubber feet to put under this print so you don't ruin your desk, but it works fine without it. My...

This allows you to attach 5.6-5.8mm O/D XLR cable to a Rode PSA1 microphone stand.This is a remix of this cable clip on Thingiverse. Credit to <a href="https://www.thingiverse.com/silence1337v">silence1377</a> for the original design, I just enlarged...

Rode PSA-1 microphone boom arm wall mount. ...Will most likely work with other microphone arms that have a 13mm diameter shaft that go into the base.

A small tab that clips onto the psa1 microphone holder to put your headphones on.

Hello,&nbsp;i could only find clip's for mic arms with 10x10mm bar's but the Rode has 12x12 so they dont fit. That's why i made one myself.&nbsp;</p><p>It “works” great, mostly, holds the cable well without crushing it (not like you could crush an...

FR : C'est simplement un clip pour tenir un cable de 5mm de diametre sur le Rode PSA1. ... EN : It is simply a clip to hold a 5mm diameter cable on the Rode PSA1.

FR : C'est simplement un clip pour tenir un cable de 5mm de diametre sur le Rode PSA1. ... EN : It is simply a clip to hold a 5mm diameter cable on the Rode PSA1.

I have a Rode PSA1 boom arm. It is a great piece of gear. The only problem is that it has a clamping mechanism designed to be attached to a table or desk. I have a glass topped desk and so the clamp has always been a problem for me. I wanted to be...

**DO KEEP IN MIND** The Rode PSA1 is a scissor style boom arm, this bracket i have designed is made to only fit when it is in its smallest collapsed form. If it fits loose then widen the scissor arm a tad, too much may end up snapping it. I might...

Basic useful cable clip for the Rode PSA1 desk mic arm. Drawn in Fusion 360. ...

Basic useful cable clip for the Rode PSA1 desk mic arm. ...Drawn in Fusion 360.

A simple clamp to prevent the the RODE PSA1 microphone studio arm from swinging out while not in use.

Cable Clips for the RØDE PSA1 Microphone Arm equipped with the RØDE NT-USB. I use 8 clips in total for the whole system, 4 on each rod. Print in Vase-Mode with 0.4mm line without any skirt/brim. ... By pushing the cable in, a little tension is...

RODE Procaster Broadcast Dynamic Microphone and Rode PSA1 Professional Studio Boom Arm with realistic detail

This is a wall mount I designed to hold my Rode PSA1 Mic Arm. I had recently reorganized my desks and my primary desk is only 24 inches in depth, which with 3 monitors on it causes the mic arm to have no extra room to move around. I wanted to mount...

This simple knob is designed to ease rotating the microphone on a Røde PSA1 microphone arm without touching the microphone itself. ...Additionally, it provides better grip in order to fix the microphone securely to the arm.

This simple knob is designed to easy rotating the microphone on a Røde PSA1 microphone arm without touching the microphone itself. ...Additionally, it provides better grip in order to fix the microphone securely to the arm.</p>

It was annoying for me to have some loose cables at the arms of the Røde PSA1. So I designed this, to enclose and Mount the microphone cable at both armparts. It has a nice and tight fit and holds onto the arms without any tape or so. I...

Wall Mount for the [RØDE PSA1 Studio Boom](http://en.rode.com/accessories/psa1). Uses the supplied desk-insert style attachment. The optional headphones extension allows for hanging your headphones below the boom mount. ... If mounted on a concrete...

The first version i made clamped to 2 arms which can restrict movement. In V2 you can simply clip it to 1 arm and have free range of motion. Requires less filament material but i do recommend 10% infill given how skinny the hook arms had to be in...

It was annoying for me to have some loose cables at the arms of the Røde PSA1.So I designed this, to enclose and Mount the microphone cable at both armparts.It has a nice and tight fit and holds onto the arms without any tape or so.I attached 2...

<p>This model was necessary to clear up my desk space, to get stuff off the table.</p><h4><strong>Parts</strong></h4><p>For assembly you will need:</p><p>printed parts</p><p>For parts print the following:</p><p>1 x...

This object is a replica of Rode Microphones VideoMicro. There is a 3.5mm jack jack on the back. ... After a few excavations, the retaining part has expanded in my case due to the type of material but with PET-G this can be completely avoided.

This is a fiching rode holder made for a rode of 0,4 and 1 cm of diametre . ... C' est pour attacher une canne a pêche une fois pliée avec un côté de 0,4cm et un autre de 1cm

http://www.thingiverse.com/apps/customizer/run?thing_id=1013494 Instructions Using the following options: labelDepth = 2 textHeight = 2 style = Pacifico labelHeight = 20 labelStyle = Indent oneOrTwoSticks = One labelWidth = 96 stickWidth = 10...

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=78727 Instructions Using the following options: build_plate_selector = 0 label_text = rode peper build_plate_manual_y = 101 build_plate_manual_x = 104 font = write/Letters.dxf

http://www.thingiverse.com/apps/customizer/run?thing_id=1013494 Instructions Using the following options: lettering = Rode Uien labelStyle = Indent textNudgeY = -2 textNudgeX = -10 style = Pacifico indentEdgeWidth = 1.05 labelDepth = 2 stickLength =...