roku tv legs 3d models
64004 3d models found related to roku tv legs.thingiverse
My sons TCL 43" Roku Tvs base legs were to short to fit his Xbox One and cable box under it so I designed 70mm tall ones and printed them on my Ender 3 Pro. ... These fit perfectly using the existing screws.
thingiverse
Fold-able legs/stand for TCL TV so that you can fold them in and hang the TV on a wall (I have a wall mount I will share seperately)
prusaprinters
Fold-able legs/stand for TCL TV so that you can fold them in and hang the TV on a wall (I have a wall mount I will share seperately) Category: Replacement Parts
thingiverse
this is a shorter and simpler version of the 3DbyJB TCL ROKU tv leg. this will fit 40in and 43in TCL Roku tvs. ...
thingiverse
The base was built for the "TCL 55S405 55-Inch 4K Ultra HD Roku Smart LED TV (2017 Model)" and provides well needed support. ...The legs of the TV fit in the two holes of the base.
thingiverse
I used 3M Double Sided Tape to hold the Roku 3 in place as well as to a fix the mount to the bottom of the TV.
thingiverse
This is a a bracket that will fit into the slot intended for attaching the TV stand to a 42" Vizio E-Series TV, with a little shelf on it that's sized to fit a Roku.
thingiverse
This is a shelf that can be used to sit a Roku on top of a TV. The stl is currently configured to support a Roku Premiere, but I'm sure it could support many other types of set top boxes. This is also configurable in customizer, so you can use it for...
thingiverse
Made a few changes to "The Ultimate Dad Roku Remote!". Easier to print now with no supports. ...:)
myminifactory
The double sided tape didnt seem to do the trick for my roku so I made a custom holder thats low profile. ...Acomadates screws if your daring but super glue or other adhisives that are more reliable than doublesided tape should be more than enough.
thingiverse
a little shelf to help your rook sit atop a flatscreen tv. ... I have used it for a Visio and a Dynex tv.
thingiverse
a little shelf to help your rook sit atop a flatscreen tv. ... I have used it for a Visio and a Dynex tv.
thingiverse
Remixed to add more surface to use double sided adhesive and a limiter to hold it in place in case the cables are pulled from behind (usefull for articulated TV support).
thingiverse
Simple holder for my TV and Roku remotes to hang on the wall in my garage. ... Easy to rescale if needed for different size remotes.
thingiverse
Mount for Roku 2 to go under the TV. ... There is a tab on the top that a 3m strip can attach to for mounting.
cults3d
TV Stand for use with Roku Express, it is very easy to place it on the TV and adjust it by opening or closing its base, do not forget to place the base that bears the text ROKU in front of the base. Updated design for 38.5mm profile TVs. ... If you...
prusaprinters
I also have come to increase the bed temperature to 65C for large prints to reduce/remove warping near the edges.TV Remote: Vizio TV Remote Replacement by Philips (Universal Remote Control Compatible for Roku, Apple TV, Smart TV, Soundbar, Streaming...
thingiverse
TCL roku 32" tv model 32s327 stood too tall for my wife's desk, so i made some low profile feet for it. ...thought someone might have a need for them even though they're a simple design
thingiverse
I modified the Lid of the Roku TV Remote Case by David041799 so that it would work for my Hisense Roku TV Remote.
thingiverse
Roku Ultra mount will utilize the vesa tv mount on the back of most modern TVs. No need to use adhesive to attach the mount, just use a screw to attach the mount. I used a M6 x ~15 screw for a Sharp TV. ...
thingiverse
This is a mount for an Insignia Roku tv remote. There are so many roku remotes at this point you'll just have to see whether its the same as yours. It's designed to have a command stip put on the back and to be stuck to a wall, coffee table, back of...
thingiverse
A simple clip designed to mount the Roku Express streaming box on the top of a slim TV or monitor. I've provided the files for the complete clip in a single piece or two separate pieces, which makes printing without supports easier. ... The separate...
thingiverse
The Hisense HS214 soundabar doesn't quite fit between below the Hisense 43" Roku TV (why Hisense, why?) so I needed a part to raise it up. [protius2](https://www.thingiverse.com/protius2/designs) made this [television lifting...
thingiverse
This is designed for the Roku TV remotes with the (4) vertical app buttons as opposed to the block of 4. I do not have one of the other remotes handy so I'm not sure if it will work for that one or not. I printed this with 25% infill and used a...
thingiverse
Holds both a standard Roku TV and Amazon Fire TV remote. ...Got tired of constantly searching for remotes and/or throwing them on tables, so I made this.
prusaprinters
The Hisense HS214 soundabar doesn't quite fit between below the Hisense 43" Roku TV (why Hisense, why?) so I needed a part to raise it up.protius2 on thingiverse made this television lifting shoe for the same TV but it was too tall for my needs. I...
thingiverse
A simple Roku remote stand/holder Printed with 50% infill to make it denser and heavier for stability. Not needed if you are planning on sticking the bottom to desk or table with tape. Added a taller version that is more stable and has the Roku logo...
thingiverse
I was gifted a really nice Sanyo TV but one of the feet was broken. These replace the existing feet and look pretty nice. ...
thingiverse
Adjustable TV mount for Roku Express/Premiere. ...It has two clip sizes for different TV thicknesses.
thingiverse
Made these for the series 5 50S535-CA because the legs were too wide. I've included the part files as well, print with at least 70% infill, don't need support but up to you. Please not you must print both copies, the left side has a slightly...