roku tv mount 3d models

a little shelf to help your rook sit atop a flatscreen tv. ... I have used it for a Visio and a Dynex tv.

a little shelf to help your rook sit atop a flatscreen tv. ... I have used it for a Visio and a Dynex tv.

I used 3M Double Sided Tape to hold the Roku 3 in place as well as to a fix the mount to the bottom of the TV.

This is a mount for an Insignia Roku tv remote. There are so many roku remotes at this point you'll just have to see whether its the same as yours. It's designed to have a command stip put on the back and to be stuck to a wall, coffee table, back of...

The Apple TV has to be visible, so I decided to take an Apple TV mount, and put brackets on it to fit the TV. It worked quite well. The reason the brackets look a little rough is because I made a mistake on this print and printed it at 100% infill -...

Open in Customizer to design you own. ...The pre-populated values are for an Nvidia Shield.

Customized version of https://www.thingiverse.com/thing:3255257 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3255257

This is a a bracket that will fit into the slot intended for attaching the TV stand to a 42" Vizio E-Series TV, with a little shelf on it that's sized to fit a Roku.

Mount for Roku 2 to go under the TV. ... There is a tab on the top that a 3m strip can attach to for mounting.

Roku Ultra mount will utilize the vesa tv mount on the back of most modern TVs. No need to use adhesive to attach the mount, just use a screw to attach the mount. I used a M6 x ~15 screw for a Sharp TV. ...

I created a strong and robust Roku TV remote holder/wall mount. There is a counterbore for a screw with less than an 8mm head diameter so it can be wall/desk mounted. The bottom could be adhered to a flat surface so that it could be used as a stand...

... in half to fit the Ender 3 printer bed. Printed in Low Quality 0.28mm and 80% Fill. Dimensions were right on point, just needed to file the 2 bottom holes. File is available at https://www.tinkercad.com/things/jevKAF9KCq1-roku-streambar-tv-mount .

Adjustable TV mount for Roku Express/Premiere. ...It has two clip sizes for different TV thicknesses.

I remixed the Roku XS wall mount by Brett, http://www.thingiverse.com/thing:34848, and added a mount to fit my TV. This should fit any TV with a VESA 100 (spacing between the holes that you would attach a wall mount to). I have made the holes that...

TV Mount for a Roku which sits on stop of the TV. This will fit a TV with a 14mm thickness at the top. I also included the sketch up file if you want to modify it to fix a different size TV thickness. Send me a message and I will be happy to...

Not all Roku Ultras are created equal. ...This mount is for the updated Roku Ultra 2020, model # 4800X. Device can be inserted with ports facing either up or down. Attached using velcro. ... Printed vertically with supports at .20mm.

Not all Roku Ultras are created equal. ...This mount is for the updated Roku Ultra 2020, model # 4800X. Device can be inserted with ports facing either up or down. Attached using velcro. ... Printed vertically with supports at .20mm.

... all Roku Ultras are created equal. ...This mount is for the updated Roku Ultra 2020, model # 4800X. Device can be inserted with ports facing either up or down. ...Attached using velcro.</p><p>Printed vertically with supports at .20mm.</p><p>&nbsp;</p>

This is a TV mount for a Roku Ultra. Print the part with supports for the internal cavity, and attach to the back of your TV with an M4 screw to the VESA mounting points. Currently made for a TV. ... Can be fully edited or customized in Fusion360...

This is a TV mount for a Roku Ultra. Print the part with supports for the internal cavity, and attach to the back of your TV with an M4 screw to the VESA mounting points. ...Currently made for a TV. Can be fully edited or customized in Fusion360 using...

A simple Roku 4 mount which can be drill and mounted to the back of a TV or the wall. ... OnShape FIles: https://cad.onshape.com/documents/22cf5ba2a5bd3e4e742bf625/w/fff3ecb18c7e2174d10fcffd/e/a9512e2c919459721480c00f

Mount to place cable box or AppleTV/Roku on top of flat screen TV. This was made to fit a TCL 43" TV, but could probably fit most flat screens with minor adjustment to the center part that props against the back of the TV. Fusion360 file is included...

Customized version of https://www.thingiverse.com/thing:148002 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=148002

Simple Roku 2 TV mount Designed for fast printing with no supports. Practical not pretty attach with hooks or paper clips. ... Print Settings Printer: Flash Forge ...

The base was built for the "TCL 55S405 55-Inch 4K Ultra HD Roku Smart LED TV (2017 Model)" and provides well needed support. ...The legs of the TV fit in the two holes of the base.

... without double sided tape. ... Mount is screwed in with 2 #4 pan head screws. Feed the wiring to the Roku from the back and slide it in place. A small bump on the bottom of the mount helps keep the Roku from sliding back out unintentionally. ...  

This is a shelf that can be used to sit a Roku on top of a TV. The stl is currently configured to support a Roku Premiere, but I'm sure it could support many other types of set top boxes. This is also configurable in customizer, so you can use it for...

Made a few changes to "The Ultimate Dad Roku Remote!". Easier to print now with no supports. ...:)

The double sided tape didnt seem to do the trick for my roku so I made a custom holder thats low profile. ...Acomadates screws if your daring but super glue or other adhisives that are more reliable than doublesided tape should be more than enough.

Remixed to add more surface to use double sided adhesive and a limiter to hold it in place in case the cables are pulled from behind (usefull for articulated TV support).