rope modeling

This thing for Archambault Surprise 25 build 2001 or later. ... Ropes tend to be caught between the traveller car and the hull. This little plastic thing prevents the rope jamming in 90% of the cases. It fits the 22mm wide rails e.g. ...from Harken.

A 3D-Printed Replacement Playmobil Rope Ladder/ Mast Rigging. Set pictured is the Playmobil Schooner Ship, set# 3055, 3740, & 6348. The rope ladder is approximately 12-5/8" inches long, with 17 rungs. Lays down flat on the build plate, with...

Here is a 3-holed line cinch-up for tent guys. ...I've made one similar to what's included with some tents. It fits my 5/32" nylon braided rope as well as paracord. ...Easily scales up or down for any size rope.

... it. Determine correct length of rope for height of individual (http://www.rxsmartgear.com/how-to-size-your-rope/) thread the caps on and tie a single simple knot to secure, trim and screw cap down to handle body. ...Repeat for other end, and enjoy!

... for my rope. The hole is perfect for para-cord and a single knot fits inside the tapered hole in the handle. I suggest sealing the ends of the rope by heating it with a lighter to keep the rope from fraying. ... Category: Replacement Parts

Model with a rope. Sailor in the American Independence War. Union armies. The model has a circular, elliptical base or other shape (depends on the model). the characteristics are shown in the images of the web. (The written information may have...

Able to be printed in PLA, LED's do get lukewarm to touch but no where near hot enough to melt PLA. The uploaded model was created using a slot width of 6mm, a height of 11mm and a floor height of 1.2 (3 layers of 0.4mm layer height / 6 layers of...

Each handle consists of three parts, the front and back of the handle and the knot holder.The picture shows one of the handles after seven months of use so it's a bit battered but still working perfectly fine.PrintingPrinted a full set of two handles...

... and hand soldered connectors. This shape requires 0.7m of rope, so will need a 12V DC 1A power adapter. If you're in the UK I recommend 3DQF Filament Please also see my Snowflake and Stocking and Present/Gift and Gingerbread Man and Candy Cane

Dia 22 mm stainless wire rope ani vibration mount can be made using this unit.These mounts are without rubber,and hence long lasting.They are used in compression,shear or combination.They can keep out very low frequencies out.

Customized version of thing:363800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=363800 Instructions Using the following settings: Rope Diameter = Six Wheel Diameter = Sixty-Four

I Constructed a Wall Mount for My Harbor Freight Rope Light Solar Panel Using a 6-32 Tap, Printing It with At Least Four Top/Bottom Layers and Three Shells.

Designed this for a friend, but figured maybe others could use it as well. ... The electric fence isolator is designed for 7 mm wire/rope used for horse enclosures.

This tool is used to neatly store your paracord pull-up rope until you need to pull your bow or firearm up to your tree stand.You can attach the tool to yourself so that it unravels as you climb.

A pulley block designed specifically for a 6mm rope is utilized. ...To achieve this, I chose to use an aluminum tube with an 8mm diameter and a 1mm wall thickness as the pivot pin.

We're showcasing a straightforward clip designed specifically for securing a 6mm cord or rope. This user-friendly tool enables individuals to easily thread items onto the cord before securely clamping them in place. ...Thanks for your consideration.

I run rope mods on my Hawk Helium sticks, and unwrapping the rope from around the stick was mildly annoying when deploying. This allows you to add a piece of 1/8" shock cord through the channel to wrap around the stick to help hold and manage the...

I crafted a flexible exercise pull rope minus the grip and couldn't locate an alternative, so I fashioned one myself. ... You can find more DIY projects on my channel at https://www.youtube.com/c/ELECTRONOOBS.

It is the replacement of the hooks for the shelf holding rope in the trunk of the RR Evoque. ...Instead of using clip as in the original one, I've made a pin and used CA glue (superglue).

... I attached the two pieces by tapping threads into the rope cleat and used M3 screws. It should fit snug over the rail. ...The long side of the rail clip should be on the side where there's downward force.In this case, on the outside of the rail.

This is a proprietary wall mount for the BEAR KOMPLEX SPEED ROPE. See photos for reference. Print it facing right side up (as though it were wall mounted). Make sure you have support selected for the screw holes so they print nice and even. My print...

Manchon for jumping rope is made to withstand rough handling and harsh outdoor conditions, ensuring it stays securely attached to your hands even during high-intensity jumps. Crafted from durable materials, this grip fits comfortably in your palm,...

... is now available, measuring exactly Range 1 in length (6 inches / 152mm). +A Climbing rope has been added, measuring 5mm wide and exactly Range 1 in length (6 inches / 152mm). ...The rope features a 1mm flat back for easier printing and gluing.

This guide is meant to be mounted on the window frame and should work with various brands' designs, although I suspect Ikea has already modified their curtains to include a pull mechanism inside the roll rather than an external rope. ...Our newer...

... to it. Determine the correct length of rope for your height (http://www.rxsmartgear.com/how-to-size-your-rope/), thread the caps on and tie a single simple knot to secure, trim and screw cap down to handle body. ...Repeat for other end, and enjoy!

Ring reserve for free 11.4 mm engraving 1.6 mm rope Piece size: 25 Diameter: 20.69 Weights: 18 k yellow and red gold : 15 grams 14 k yellow and red gold : 1 gram 18 k white gold: 14 grams 14 k white gold: 13.7 grams Platinum 950: 20.5 grams Silver...

A good screw length that makes it easy to insert the rope while the clamp is open is the height of both clamp parts, plus the rope diameter. For the 4mm rope clamp, that's about 4.1 + 4.1 + 4 = 12.2mm. Select a screw of about 12mm length. For the...

Instead of tying the ropes directly to the tarp, I wanted a method to easily connect and disconnect the ropes so they wouldn't become tangled every time the tarp was folded. I also desired to add some bungee cord to each connection point on the tarp...

... para-cord for my rope. The hole is perfect for para-cord and a single knot fits inside the tapered hole in the handle. I suggest sealing the ends of the rope by heating it with a lighter to keep the rope from fraying. Category: Replacement Parts

The hook firmly grips both the gutter and the rope light, ensuring each installation provides a stable mounting point and maintains optimal positioning. For optimal results, it's recommended to print this design using a UV-stable material. ...I've...