rose with thorns 3d models

I designed two different stems, one with and one without thorns. The attached oscad script lets you select number of thorns and angle, then evenly spaces them vertically and radially around the stem. Note: The rose petal STL is from thing 152642...

Customized version of https://www.thingiverse.com/thing:245722 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=245722

Customized version of https://www.thingiverse.com/thing:245722 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=245722

Instructions Rose with Thorns & Stem & Bits I didn't modify the rose, but everything else is brand new from scratch. Printing: I printed everything at .2mm layer height with no supports or raft, 10% infill (though not much actually uses infill, you...

I wanted a more complete Rose, so I took a basic rose and added stuff :) Both open and closed versions. Thorns can be a single color, 2 color glued, or dual extruder. Added vase mostly stolen from Microsoft's Rose (I like this rose better though).

Сut off the receptacle on the stem.

this model created in Zbrush and have polygonal geometry

... raft can be useful (I've printed it without raft). Sepal requires supports quite heavily. Post-Printing You can "glue" everything with just heating it up (I use torch lighter). ...I would also recommend shaping leafs manually after light heating.

... with no supports. Also add a stem hole. Designed my own rose stem with thorns. Stem may need supports at least buildplate supports. ... There are variations: larger leaves and a rose base TIP: Use a heat gun to re-shape leaves and branches.

Just a picture I made of Jesus with the crown of thorns

... suggests that it was intended as a single devotional image. The image of Christ with the crown of thorns provided a powerful example of his endurance in the face of suffering, and such figures were often placed in side-aisles or in special chapels. 

Although this crown was awesome already, I needed one with even more spikes! This is human sized. ...Image of testprint has been scaled by -75% This HAS NOT been tested!

This door is usable with dragonlock system. ...It has the same measurements as a regular dungeondoor.

Thorns

Same as the other but with a few thorns

Face of Jesus Christ with base Approximate measurements in diameter of 65 mm and thickness of 9mm to hang in bedroom, living room, office, etc.

This is an organizer for the board game Black Rose Wars and the expansions Hidden Thorns, Inferno, Sator Box. The school and mage from Chrono also fit but the Chrono miniature does NOT. It will all fit into the base game, Hidden Thorns, and Inferno...

The school and mage from Chrono also fit but the Chrono miniature does NOT. It will all fit into the base game, Hidden Thorns, and Inferno boxes. It works with premium sleeved cards but is probably NOT for you if you want to paint your miniatures!...

Jesus crowned with thorns / Gesù coronato di spine

this ring is a special design with thorns and is very modern very extravagant

DND Mini

House number with a name. ...Decorated with thorns. A very decorative and unique. ...

DND Mini v.2

I've added a stem to use when you don't have 3mm filament. ... One side is a bit flatter to make it print more nicely.

DND mini figure

Although there are some slight undercuts, it was created with molding and casting in mind. ... Inlcudes a highpoly, quad OBJ (1 Mil polys) and a decimated, optimized STL (300k polys) Nominal size (although easily adjustable in any 3D software) is: 40...

Elvis Lithophone with Rose

A rose bud with a stem.

Intermittent thorn wheel

Intended for scenery use, there are six variants in total on my Patreon for $1. I have scaled them to a medium dnd size (The large one I scaled up to be 100mm tall before printing). ... Enjoy :) https://www.patreon.com/L_dext