rostock dual extruder 3d models

Sand the main hole of the effector plate in order to gain some space between the extruder hot end and the effector material. Else you may just burn it away. About 4 mm of space is ok. I used a 10 mm hobbing cutter and a dremel. Plug in the hot...

This is a dual extrusion mount for the Rostock and Rostock Mini. It is still a work in progress but will mount below the center platform. I am working on a new version to allow greater build volume height. Sorry about the pictures, my filament jammed...

I printed http://www.thingiverse.com/thing:214536 to use dual extruders but then my filament fan was too far away to do any good. So I whipped this up and it works like a charm. Requires http://repables.com/r/155/ stl file to compile the OpenSCAD...

These are the pieces I designed to use with the Rostock Max V3 Dual Extruder kit to put it on your Rostock Max V2. This includes a new mounting plate for both extruders, as well as a new dual spool holder design. No drilling is required, however...

... gear units on 0.9 degree stepper motors. (https://www.amazon.com/WINSINN-Extruder-Creality-Upgraded-Aluminum/dp/B07SY745CF/ref=sr_1_1?keywords=dual+gear+extruder&qid=1582048501&sr=8-1) Haven't tested it yet. ...Please let me know if any issues.

Remixed Solidude's vertical plate mount to allow for extruders other than the stock SeeMeCNC EZ/EZR units, and added support for a second extruder while I was at it. This will let you use a Titan, BMG, or other mount-to-NEMA17 type extruder unit.

Someone requested a dual setup so here it is to use!

I don't know if this is useful for other printers or not, but I made it to go on the dual extruder mount that I had previously downloaded and printed for my Rostock Max. It holds a 25mm fan, but needs a shim on the side to hold it in place quietly. I...

I don't know if this is useful for other printers or not, but I made it to go on the dual extruder mount that I had previously downloaded and printed for my Rostock Max. It holds a 25mm fan, but needs a shim on the side to hold it in place quietly. I...

This is a working dual extruder hotend and effector platform modification for the Rostock Max V2. The goal was to mount two E3D V6 hotends in the stock above-the-platform position by creating a new effector platform with a wider center hole. While...

The is for Dual ProStruder's on my Rostock Max V2. Just another design for my Prometheus System setup. It fits in the stock cutout on the top piece. You'll have to install the ProStruders after putting the top piece in place (wire to the motor and...

Experimental yet fully working direct drive extruder for Rostock delta printer without Bowden tube. The design was made for easy conversion of Airtrippers Bowden extruder and uses almost the same parts. The parts required are a Nema 17 motor with...

This is a design I've made for my Rostock that allows quick-changing (sort of) of extruders / end effectors on my Rostock Max. ... There are several parts: Top Coupler: Attaches to the triangular mounting plate on the MAX Bottom Coupler: Generic...

The nice thing about my solution, is that it may fit many other extruders using this same lightweight stepper, as the mount locations are set by the motor, and not the particular extruder you want to use. ...

Here is a dual hot end mount, specifically, the HE280. It requires minimal modification to the stock effector platform . Sure, I could have placed it below the effector platform and not had to worry about cramming everything into the small space,...

Finished Credits Inspiration While I may have built this from the ground up, Dave Singh's Rostock Max V2 TPE / Ninjaflex Custom Extruder started my journey to design one myself. There are some similarities, so I listed this as a remix. ...My Ninjaflex...

I made a quick spacer to help reduce the noise coming from my extruder. ... Instructions I printed at 100% in ABS

Hardware: 3 - M3 x 8mm screws (mounting extruder to stepper motor) 1 - M3 X 25mm screw(mounting extruder through lever arm to stepper motor) 1 - M3 x 16mm screw (for mounting bearing onto lever arm) 5 - M3 washers 1 - M3 nut (for mounting bearing...

TPE 80A is softer and more flexable than Ninjaflex I felt there were also a few deficiencies in Singh336's extruder so I decided to create my own. While mine is created from scratch, it is heavily based on the design by Singh336. Benefits: The...

So, I've made the following tweaks to the v7 Extruder Maximus: - Increased the hob gear hole diameter to accommodate the 12.4mm hob gear. Note: This will still work for the smaller gear. - Carried the arm restraint all the way around on the top for...

So, I've made the following tweaks to the v7 Extruder Maximus: Increased the hob gear hole diameter to accommodate the 12.4mm hob gear. Note: This will still work for the smaller gear. Carried the arm restraint all the way around on the top for...

... E3D hotends. ...You lose some height because it attaches at the bottom of the platform but you gain an awesome dual setup. Check out the SeeMeCnc forum for dual hotend settings http://forum.seemecnc.com/viewtopic.php?f=54&t=1946&hilit=dual+extruder

Replacement for the three spacer parts that hold the extruder and its stepper motor to the extruder bracket on the Rostock Max V2.

Attached is a mount designed to fit the MK7/MK8 extruder at the bottom of the Rostock Mini. It utilized the original mounting location for the experimental Airtripper that was with the included with the design. However, I wanted to try out the MK7...

My Rostock Max V2 struder broke a connection, I replaced it with the new EZR Struder, and the bolts were the wrong length for the stock spacers. I have noticed how noise is transmitted up the solid attachment, and decided a flexible attachment would...

Replaces a Rostock max V2 side panel and allows two DPS-1200FB server power supplies to slot right in the side and latch in. They exhaust their hot air directly out of the printer this way, and provide both 12V and 24V rails. One must be modified to...

This thing is just a mount for PG35L extruder and E3D hotend.

PG35L Extruder: http://www.thingiverse.com/thing:43457 E3D Fan Duct: http://www.thingiverse.com/thing:91413 I located the extruder at high position using this mount so that the PG35L motor did not disturb the movements of diagonal rods. Three sets...

This is a support for dual extruders.

Its a mount for dual extruder for left hand and right hand MK8 extruders.