rostock max 3d models

Enclosure Part for the Rostock Max V2 or any other printer if you modify the design

An LED ramp I'm testing for using on my Rostock MAX

Remixed for Rostock Max V3. ...This design uses existing mounting holes for support panels so you won't need to drill into the frame of the printer.

... the Rostock Max V2 arms (they may work on the v1 too.. ...haven't tried) to reduce lash. As such, they should be printed from Ninjaflex or a similar TPE material. Instructions if printing on a rostock max... print very slowly. ... i have to print at

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Infill: 30% Notes: Printed on Rostock Max V3 with PLA How I Designed This Remixed from http://www.thingiverse.com/thing:1664735 . I added tabs to this design that...

This spool fits the Rostock Max and holds a kg of filament. Also see http://www.thingiverse.com/thing:116104 for a one piece custom spool. ... This is a customized version of http://www.thingiverse.com/thing:45101

A door hinge that allows the user to remove the door from the SeeMeCNC Rostock MAX. They fit into the existing holes, just have to shave the tabs off of the TOP of the door and install this hinge as a plug. Works well, has survived the test of...

This spool fits the Rostock Max and holds a kg of filament. Also see http://www.thingiverse.com/thing:116104 for a one piece custom spool. This is a customized version of http://www.thingiverse.com/thing:45101 Instructions I put the two parts of the...

This allows a Rostock Max style printer to serve part time duty as a PnP (Pick and Place) machine. Only requires an additional stepper port, Heater2 port, two pwm fan ports, and an always on fan port. Rambo, Smoothie, Duet type boards should...

... of dreading it. Requires x6 drill holes in the top of Rostock Max V2. Use a template for accuracy before drilling or mark where you want the holes and remove the top to drill. ...Drill press recommended or tool to ensure perpendicular Drill Bit.

This fan shroud fits SeeMeCNC's Rostock MAX 3D printer, for cooling workpieces as you print. It's built for a 4cm (40mm) fan. Supports are included as part of the model. Instructions I felt like this...

The dimensions work out to match the existing hole pattern in the rostock max "cover brackets" so no drilling is required, only screws and nuts. The brace.stl is held to the cover brackets with one screw and one cable tie. The cable tie goes...

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Resolution: 0.3 mm Infill: 40% Notes: Clear ABS (with unusually high 'shrinkage' factor) printed upside down. ...If your printer doesnt bridge well, you might want to...

If you want to illuminate your cabinet, here is the rocker switch box I modeled: http://www.thingiverse.com/thing:1421639 and here are the extrusion mounts for the LED strips: http://www.thingiverse.com/thing:1702064 Print Settings Printer Brand:...

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: Doesn't Matter Resolution: 0.2mm Infill: 100 percent Notes: Printed @ 0.2mm layer height with a 0.4mm nozzle using ABS with 100 percent infill. The only support I used...

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Resolution: .20mm Infill: 20% Notes: You can use any plastic. I was testing some Phileex PLA. Post-Printing The brackets snap on and the shield sits in the groove. I...

These are the brackets needed to make an enclosure for your rostock max v2. You will need 3 base and 3 top pieces. You can print 3 at a time with the build area. Locate the brackets on the extrusions and bolt the brackets to the rostock's top and...

I wanted an enclosure for my Rostock Max V4 and it was so new i couldn't find one already being shared on Thingiverse. So I started designing this one. most parts are 3d printed and bolt on using factory hardware. I am terrible at documenting...

This is a full enclosure for the SeeMeCNC Rostock Max V2. It has double doors on all three sides that swing open fully allowing easy access to the build area. I designed this enclosure to create a heated chamber and to (hopefully) capture the...

Rostock MAX - Delta 3D printer http://seemecnc.com/ http://reprap.org/wiki/Rostock_MAX

A calibration test for the Rostock Max V3 printer bed

A camera arm for the SeeMeCNC Rostock Max. ... Modified so that you can attach and remove it much easier.

This is the stock extruder platform for the Rostock Max V2 with 3 tabs for layer fans.

Replacement for the three spacer parts that hold the extruder and its stepper motor to the extruder bracket on the Rostock Max V2.

This is an adapter to use HugoHuge's Filler on a Rostock Max V2. ...It slots in place of the original laser cut spool holder arms.

This is a simple adaptor I designed so that I could mount a Raspberry Pi behind the LCD panel on my Rostock MAX.

Needed a space for my tools so i designed this drawer to use up the empty space in the Rostock Max v3 front panel. ...Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: Yes Resolution: 0.15 Infill: 15%

Some measurements reverse engineered from Rostock MAX Delta 3D printer from by SeeMeCNC This will most likely need to be printed with supports. It replaces the carriage assembly from the Rostock Max and should be compatible with the V2 and V1, but I...

Efficient and and printable 40mm fan duct for the rostock max. Instructions Modeling with openscad. Could print it in PLA without support material. ...Bind to platform with 3 cable ties going through...

Upgrade to the Rostock Max V2 Spool Holder.  Three parts, spool holder and threaded cap, arm.  The spool holder has a 13X13 mm square hole that the arm is glued into.  Can redesign arm to fit many different type mounts.