rostock max v2 upgrades 3d models

After upgrading to the 713Maker mount (http://713maker.com/mounts.html) for my E3Dv6, I found that the original slim fan shroud was too small. I remixed Noircogi's design to be both longer so it'll reach the print area, and added a gap in the middle...

After upgrading my E3Dv6 with the 713Maker mount (http://713maker.com/mounts.html), I discovered that the original slim fan shroud was woefully inadequate for its new surroundings. To rectify this situation, I decided to remix Noircogi's design,...

After upgrading to the 713Maker mount (http://713maker.com/mounts.html) for my E3Dv6, I found that the original slim fan shroud was too small. I remixed Noircogi's design to be both longer so it'll reach the print area, and added a gap in the middle...

The MAX METAL frame's horizontal crossmembers boast two channels, allowing these clips to be positioned directly above or below other accessories without any hindrance. ...To secure them to the frame, use Unbrako #10-32 x 1/2 low-head caphead screws and...

Options in Use: Tower Side: Set at 20 Bottom Temperature: Precise Setting of 215 Degrees Emboss Height: Optimized to 0.5 Millimeters Height Increment: Standardized at 10 Units Indentation: Consistent Margin of 2 Units Tower Height: Customized to...

Alright, let's dive in. There are several versions to explore. Version one combines a makerbeam mount with an iPhone case, all encapsulated within the file makerbeamiPhoneHolderSupported.stl. Version two takes this combination to the next level by...

Print strong, but without specific temperature restrictions. This piece fits well with https://www.amazon.com/AccuRemote-ELECTRONIC-INDICATOR-Functions-conversion/dp/B006YD7G36/ref=sr_1_25?ie=UTF8&qid=1465888680&sr=8-25&keywords=dial+indicator. This...

A smaller MAX jar

I was not happy with the kickstand options for the TX16S max, so I decided to make something a little better looking. Printed without supports, make sure to insert the washers back into the transmitter side. I also had to use slightly longer 2mm...

Alternative LCD mounts are available; however, wooden ones tend to split easily. To replace these, consider using a 3D printer to create new mounts and adjust the size according to your device. ...Test by printing a few layers before fitting the part,...

Belt guides are incorporated in the design of these idle machines, ensuring smooth functionality and ease of use.

Human: "Three things come to mind, but maybe it's only one. First, a wire harness for the electrical system. Second, a fan mounting system. ...Third, one of those flexible camera snakes that contractors use to inspect behind walls and through pipes."

Customized version of http://www.thingiverse.com/thing:538624 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=538624 Instructions Using the following settings: Line Height: .2 Line Width: .6 Spiral...

To maintain order near my printer, I created two designs: a basic tray and one with a tool holder for extra nozzles and standoffs. My quick-change hot end storage aids organization. For printing, I used a 0.7mm nozzle to reduce time, applied 2...

Just a remix because a i didn´t hace the 25x25x10 Fan. So i made a little ajustement to fit my 30x30x10 fan. The circle for the air flow should be bigger to be in proportion to the new fan but i did't want to slim the part since i only have PETG...

Attach a heatsink and fan to the rear of your NEMA17 extruder motor with absolute precision. Apply thermal compound, specifically Artic Silver 5, to optimize heat transfer. Harness any 12-volt power source within your system, tapping into the...

This custom-made object is based on Thingiverse's design (http://www.thingiverse.com/thing:54024) and was created using the Customizer app (http://www.thingiverse.com/apps/customizer/run?thing_id=54024). The specifications for this item include a...

Kind a spring to decrease vibrations during printing

Tighten the wingnuts on six 1/4"x20 threaded rods with tower clamps, ensuring bent fingers keep clamp from bending. Install clamps at bottom and top of each tower, aligning towers using a yardstick and cone-shaped spacers. Tighten T-slot nuts and...

Engineers implement advanced coil springs within printers to mitigate resonant frequencies. These carefully crafted coils efficiently reduce oscillations generated by the pressurized ink droplets striking the printing surface. ...The resulting decreased...

I wanted to create a body that matched the width of the chassis, so instead of redesigning all those components, I simply extended the car by adding a mid-chassis part, extending my front drive shaft, and adjusting the servo steering linkage rod. To...

After completing my quadcopter build with purchased parts, I noticed that the battery required a case not only for protection but also to secure it without relying on battery velcro straps. Furthermore, by positioning the battery at the bottom...

Hello there ! Recently I purchased the EMMI Amiibo from the game, Metroid dread, and to me it felt like it was lacking something. So here is my first iteration of the iconic "face shield" used by the EMMI robots in Metroid dread. Normally...

This is the second iteration of my Printrbot enhancements. For comprehensive details and construction guide, visit http://polakiumengineering.com/?p=2404. ...Alternatively, you can purchase this improved version from...

This upgrade set is compatible with Rostock Max V2 owners; however, you will need to purchase the V3 hotend whip and accelerometer board from SeeMeCNC separately. I would like to express my gratitude to Djkirkendall for suggesting I revisit and...

Rostock Max Users Now Have A Simplified Fan Mount Option Available To Them As An Upgrade Solution Offered By Seamecnc. The Latest Version Of Rostock Max Offers Limited Bolt-On Attachments For Fans However Still Provides Essential Spacers That Are...

... version is only for K1 Max. It measures 240mm x 240mm, 18mm height. Since the distance between anti vibration legs is short. So, it cannot go under K1.if you want to supporthttps://www.etsy.com/listing/1664907002/creality-k1-max-toolbox-v2

Introducing updated J-head mount designs for Rostock Max V1 & V2, compatible with Prometheus and e3d hotends. Two top plate options available: one for 4.8mm thick Prometheus heads and another for 3.8mm thick e3d heads. Choose from three J plate...

Existing printer designs without this dual carriage system continue to benefit from enhanced stability.\nThe printer continues to progress toward successful printing operations.\nThe bed leveling process is nearing completion following integration of...