rotating latch 3d models

The 3-D rendering of the said object has been finished and now exists in a virtual form.

This is an easy-to-use, straightforward equipment that simplifies tasks and enhances performance. ...Its user-friendly design ensures hassle-free operation, making it perfect for those who prefer a no-nonsense approach to hardware.

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters

step1: sketch geometry according to the blue prints (( !! crucial !! ...- when sketching make sure the arcs are fully defined first, then make the line under the whole cut out concentric with the axis))(note) the axis point in the blue prints can be...

The material used is AISI 1020, and it has a mass of 1066.52 units.

steps:1. created left edges sketch first2. added the curves, created relations and dimensions3. worked on right side of sketch4. added hole in left center of sketch5. added finishing relations with respect to the plus reticle thing6. extruded7.

I used the line tool to create my shape than started to dimension everything to the correct length. I used the arc tool so i could make my curves and everything. ...I than extruded than and but a circle on the shape and cut it through the entire shape.

cswa

step1: sketch geometry according to the blue prints (( !! crucial !! ...- when sketching make sure the arcs are fully defined first, then make the line under the whole cut out concentric with the axis))(note) the axis point in the blue prints can be...

Mass = 1066.52 gramsMake a sketch with a circle at the origin R6. Make a line to the left and underneath both 14 away. Make the left line 18 and between those a 45degree angle line. The bottom line running until a R5 circle's top. From that circles...

Simple FreeCad Assembly

Bolts/Nuts needed: 4 M3 x 06 Socket head bolt 1 M3 x 35 Socket head bolt 5 M3 Nuts

Steps:1. Started the sketch o the 40mm ark and dimensioned as I went, when I got to the corner with the two tangent arcs, I made the horizontal line coming from the 45 angle coincident with the point of the 29mm arc.2. Extruded to part width3.

This is one of 6 original parts I used for this assembly. The only changes I made for this part were to make it smaller so it can fit the size of the rest of the assembly. I used this part to create a 'locking' mechanism for the fridge. ...I was going...

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersProcedure: I started this model with the sketch from the front view. Started with the circle on the origin, then I sketched all the lines above and to...

I simple just followed the blueprint instructions, dimensioned the figure correctly then extruded the figure to the correct measurement.

I started by sketching out all of the straight lines and dimensioning them as such. To create the curved geometry, I used two different types of arcs. I created a centerpoint arc, using the midpoint of the long line in the bottom right as the center....

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters Process:I sketched the whole part in just 1 sketch and then did the boss extrude. ...It was relatively easy it's just figuring out the dimensions.

Use for Door Cabinet....

I utilized a secure locking device to maintain closure of the entrance gates surrounding my living quarters.

First I made a lot of dimensions to make it easier to sketch out, I started on the right slant and worked clockwise. ...After I made the sketch I extruded 45mm.

Use for Door Cabinet....

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersI sketched out a circle of radius 6, and a line 18mm long on the left, and then 2 of 45degree angles, make sure the center of the circle to the bottom...

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersI started with the circle and worked around.