runcam mount 3d models
349433 3d models found related to runcam mount.thingiverse
Runcam mount for Cherrycraft frame 24mm version used for FATshark cam. 19mm verison used for RunCam Micro. ...
thingiverse
This is a Runcam mount for the Lisam 210 drone frame. It includes a replacement side panel file for the frame which utillizes the stock uprights to add some riditity and shock absorbtion. To use this Thing, print the file normally once, and then...
thingiverse
There are two version, one for mobius and one for runcam. ...The mount hooks onto the lower horizontal standoff and then you run a strap through the slits in the frame and around the cam/mount.
thingiverse
This file has not been tested yet. ...Will update after it has been tested.
thingiverse
This is a Runcam mount for the QAV210 with a 25 degree tilt. I couldn't find a good one with the correct bolt pattern so I designed my own. ... It weighs about 8g with 10% infill.
thingiverse
This is version 3 of my Runcam mount for my F1-5. It should fit the F1-6 as well as they use the same top plate. I have removed the antenna mounts as I'm now running them below the arms. ...This has allowed me to increase the surface area of the mount...
thingiverse
A mount for the RunCam action camera. ... This is basically an exact copy of the mount that ships with the RunCam.
thingiverse
Just a simple camera mount I made for the runcam 2hd for the vortex pro ziptie it on and be done !
thingiverse
A quick and dirty mount for a Runcam FPV camera (or similar). Includes a tunnel to keep the wires neat. ...In the photo it stands a bit proud, but this is due to me using very thick Velcro™ tape.
thingiverse
30 and 50 Degree camera mount for Echo X quadcopter frame. Designed to take a piece of dual lock tape. ...I've used it with the Runcam 2 HD camera
thingiverse
... in where the stock one goes and it fits a runcam swift perfectly. You can now bolt the camera at a fixed angle and don't have to worry about the angle changing mid flight. Checking out my kratos camera mount (very similar) and kratos session mount.
thingiverse
Designed this RunCam Swift camera mount for my Kratos since the stock mount isn't good at holding the camera up. This mount allows for adjustment from 0-40 degrees maximum (This is the maximum I need for racing). It fits in the stock position with no...
thingiverse
TPU or flexible filament only. ... Perfect fit on every frames for your Runcam micro
thingiverse
This is a 12.5° angled mount for a Runcam 2 HD action cam designed to fit a Voodoo Quads VDQ250. I'm combining it with 12° angled motor mounts, so I don't need a higher angle. If you would like different angles or other modifications, please feel...
thingiverse
A small upgrade for Mobula 2c so that you can use the Thumb runcam camera. ...And fly like a micro "cinewhoop"
thingiverse
its not perfect and it might have future revisions also tx801: https://www.banggood.com/Eachine-TX801-5_8G-72CH-0_01MW5MW25MW50MW100MW200MW400MW600MW-Switched-AV-VTX-FPV-Transmitter-p-1147691.html?p=RJ05223950869201603B runcam eagle 2:...
thingiverse
i printed at 100% infill, used the 2 original screws then hot glued the front in the fuse for a sold mounting
thingiverse
S500 frame attachment for mounting a forward facing FPV camera like the Run Cam. Print Settings Printer Brand: LulzBot Printer: ...
thingiverse
... shouldn't move at all. If it does you may need to file some of the plastic away to make everything sit flush. Once installed I have added a strip of velcro to the top of the mount and hold the camera in place using the velcro and a battery strap.
thingiverse
FX-61 RunCam mount with standoff for the FX-61 Raptor RC flying wing. This mount fits the 4 holes that are already in the canopy. ... You will need six, M2.5 x 19mm screws and bolts