runcam owl 3d models
7897 3d models found related to runcam owl.thingiverse
I made this support to fix a Runcam Owl low light camera in a standard surveillance camera enclosure.
cults3d
Hallo! ... Diese Halterung wurde zur Befestigung einer RunCam Owl auf einem Opterra von der Firma Eflite entworfen. Ich habe die Halterung aus PLA mit einer 0.5mm Nozle gedruckt. Viel Spaß damit. ...Lg, Tobias
thingiverse
Hallo! ...Diese Halterung wurde zur Befestigung einer RunCam Owl auf einem Opterra von der Firma Eflite entworfen. Ich habe die Halterung aus PLA mit einer 0.5mm Nozle gedruckt. Viel Spaß damit. ...Lg, Tobias
thingiverse
Here is a Runcam owl mount for the TBS source one. ...I designed it so it can be zip tied securely into mount and then screwed with normal m2 screws into the frame
thingiverse
This is a little adapter I designed to mount a Runcam Owl FPV camera on frames with built in mounting locations for a 26x26mm HS1177 style camera. Pictured is a hive150 I am building, but it should work for other frames designed with the popular...
thingiverse
A simple RunCam Owl camera mount for 3DLabPrint EASYMAX001.
thingiverse
RunCam OWL mount for ZMR 250. ...Fixation by unsing zip-tie.
thingiverse
I needed a way to mount my new Runcam Owl in my Shendrones Shrieker quad so I designed and printed this extremely simple mount, to be attached to both the shrieker and camera with double sided tape and to give a modest 15 degree tilt. Different...
thingiverse
WIP of a mount for the Runcam Owl, to allow you to use it as an FPV camera. I'm specifically trying to build this for a QAV180 build, but I thought the community at large might find it of some use. Use a zip-tie to secure the camera to the mount, and...
thingiverse
This mount fits the RunCam Owl 2 camera as pictured. The lens opening is 17.25mm, an easy edit in Tinkercad if needed. The angle is 5 degrees down on the camera. To install, measure 60mm from the nose (before laminate) and 28.5mm to the left or right...
thingiverse
I needed a quick way to attach an Owl to a plane. ... I sort of liked https://www.thingiverse.com/thing:1369044 -- but definitely don't want any positive tilt, so I just did a similar thing.
cults3d
If any other fpv or action camera has same lens diameter (18mm) please tell me in comment Fits perfectly on Runcam OWL+ and HD 1 Lens diamenter : 18mm
thingiverse
* If any other fpv or action camera has same lens diameter (18mm) please tell me in comment - Fits perfectly on Runcam OWL+ and HD 1 - Lens diamenter : 18mm
thingiverse
RunCam Owl camera holder for Diatone ET-150 Use a zip-tie to secure the camera to the frame
thingiverse
This is a canopy for an Atom frame with an Owl cam mounted at 15deg angle (since the owl has huge fov bigger angle not needed) It uses 20mm standoffs and does not rely on the 30.5 screws used for FC and PDB. I emphasise this because I find it to be...
thingiverse
This is a camera mount for the ZMR 250 custom fit for the RunCam Owl nightime flight camera at a 10 degree angle. ... Owl fits snugly in to the mount with no hardware required and connector accessible from the back.
thingiverse
This is a little enclosure to support a RunCam OWL camera and a Quanum Elite video transmitter for FPV in one supported package that you can use as a little 'backpack' on your model. ... I've popped mine into the place that used to hold a Mobius can...
thingiverse
Basically LoveWaffle's RunCam Owl mount shoved into a frame I made that fits the Nighthawk Pro 280 in the same way as the stock fpv camera's mounting frame. Some trimming of the pegs may be necessary to create a snug fit. Tighten down the top plate...
thingiverse
This is a little adapter I drew up based on my previous runcam owl adapter. I'm transferring that build over to the SpaceoneFPV 220X frame with Aero pod designed by @babar121 and my original design doesnt seem to fit. I fugured it would make a clean...
thingiverse
This RumCam Owl camera mount for FlexRC Mini Owl best to be printed in durable flexible material which will make it virtually indestructible and will reduce camera vibrations. It consists from two equal parts which hold camera in place with the...
thingiverse
This is my remix of http://www.thingiverse.com/thing:1369044 to make it fit the RotorX Atom v1 frame. The original mount only had cradle that the camera sat in. I designed a 2 piece mount that also has a barrel that extends forward to protect the...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/lHR8xxJAN2X