runcam split 3d models
36203 3d models found related to runcam split.grabcad
RunCam Split made by Stefan Försterhttps://www.banggood.com/Runcam-Split-1080P-DVR-FPV-Camera-WithWithout-WiFi-2_5mm-FOV-130-165-Degree-NTSC-PAL-Support-64G-TF-p-1159850.html?p=3R26141006882201412NFind more FPV Cams at:...
thingiverse
This is a model of the Runcam Split PCB. ...It's just for testing purposes, 36x38mm, 2mm high, 30.5x30.5 M3 holes.
thingiverse
Case for a zoom cam project with a Runcam Split 2 The case fits over this desing: https://www.thingiverse.com/thing:2537982
thingiverse
I create this dummy of runcam split mini, just rough cube and cylinder, but the measurement is pretty close with the real thing. Just a simple dummy to fit to your project without scratching your real camera. ... To be noted, this is the first version...
thingiverse
A heavy duty case for the runcam split mini. Use 1 or 2 bolts through the case to hold it closed. ...You will needs a few mm of space behind the case to slide the cover off.
thingiverse
Case for RunCam Split 2S FOV 170 Degree Super WDR Mini FPV Camera 1080P 60fps DVR HD Recording OSD for RC Drone - with WiFi module https://www.banggood.com/custlink/m3mm8zCckz
thingiverse
... ...The frame is as Aerodynamic as possible and capable of mounting motors from 1806-2306. This Pod is Specially designed for the new Runcam Split, mounting the Runcam Split stack plate on top of the stack is probably easiest for building the quad.
thingiverse
To keep weight down I decided to give the Runcam Split a shot, but the backing didn't quite work for my build, so I created this design. Used the mount that came with the camera, and put the cable through the slot, and boom. Works great for me! ...
thingiverse
It has the exact internal space to fit the Runcam Split PCB, and the camera can be mounted at any up or downtilt angle. The lower part is open, so you can do all the wiring thought the bottom part and make it invisible. The cap locks on...
thingiverse
Because we can't buy RunCam 3 anymore, I buy RunCam Split 2 and print a housing. Get lighter HD camera than RunCam 3 and I power it from drone battery. There is space for male servo connector for power up cam. You also need 4 pcs. M3x12mm screw...
thingiverse
It a gimbal for my DIY Mavic pro build (scale 130% from original build http://diyrc.co.uk) and the runcam split cam. I use 2x 2204 and one 2805 motor. Work in progress. Quick update: Added a Gimbal Holder bracket. ...Also a bracket for the...
thingiverse
This design is intended to be used with the Growler quadcopter frame found at the following website https://armattanproductions.com/pages/kit_detail/1651 It was designed to carry the runcam split V2 as the HD camera only. This is if you do not want...
thingiverse
I kid you not you print this with zero support and use the screws that are provided to you in the RunCam split, bolt the camera on and slide the frame over the quads support frame ( tolerance is high so slowly work the 3d frame evenly on the quads...
thingiverse
Unfortunately the Runcam Split has no built in feature to auto shot in intervals when it is set to photo mode. So I made this little board to do this job. When it's switched on, the interval is set to 1 second. Each time you press the little button...
prusaprinters
This is on my 275 inch quad with 7 inch props and 1600kv motors (long range) Runcam Split mount with horizontal dipole antenna mount accessory. 38 mm space between mounting holes and 4mm hole size for vibration dampening rubber inserts used on Matek...
thingiverse
This is on my 275 inch quad with 7 inch props and 1600kv motors (long range) Runcam Split mount with horizontal dipole antenna mount accessory. 38 mm space between mounting holes and 4mm hole size for vibration dampening rubber inserts used on...
thingiverse
This is a mount for a Runcam Split Camera and an Eachine TX02 Transmitter. I made it so that I could easily mount it (and un-mount it!) to my Hubsan H501S and H501A quad. Obviously it will work for a lot of other quads. If you look close and compare...
thingiverse
This is a Runcam Split mount for the Armattan Chameleon. It uses the standard holes that come in the stock Chameleon camera mounting plates. It also incorporates a captive nut slot to use the stock tilt adjustment screws. This works best with the...
thingiverse
I wanted to add an fpv device to a tricopter I was trying to build, it was cheaper to buy the Runcam split than a gopro and after a little bit of trial and error the case was born. I think I used 30% infill but it probably doesnt need that much. To...
thingiverse
A simple universal case for the Runcam Split 3 Lite. ...(mounting holes on Runcam Split 3 Lite must be trimmed to use)
thingiverse
Runcam Split Hybrid camera cover that covers both the 4k camera and the FPV camera.