runcam split mini 3d models
121587 3d models found related to runcam split mini.thingiverse
I create this dummy of runcam split mini, just rough cube and cylinder, but the measurement is pretty close with the real thing. Just a simple dummy to fit to your project without scratching your real camera. ... To be noted, this is the first version...
thingiverse
A heavy duty case for the runcam split mini. Use 1 or 2 bolts through the case to hold it closed. ...You will needs a few mm of space behind the case to slide the cover off.
thingiverse
I have modified Nicoflood's great design to allow for approx 35mm of Tower which should be enough to clear the extra10-12mm height of the RunCam Split Mini. This is completely untested and therefore is a work in progress. ... For best printing...
thingiverse
Just a quick mount for the runcam split mini, the dimensions are correct to hold the cam firmly, mounting holes line up but will need resizing, i used a 2mm drill. The back has been left open for cooling. ... The Mount has a 5 degree tilt on base.
thingiverse
Runcam Split MINI fpv cam mount and housing for the Believer (FPV Platform). Use the existing video antenna hole on the top of the front fuselage to pull through your wires to the PDB plate. ...Looks neat and no wires sticking out!
thingiverse
My newest FPV Projekt, I made a Helmet formed Mount and Cover for my new Runcam-Split-Mini wich should easy mounted on the top of the 20x20 electronic sack. Later I will try to design some Helmet Addons like Wiking-Horns or a Roman-Brush. ... what do...
thingiverse
This is designed for the RunCam Split Mini and allows you to arrange the pieces so it can fit into the slot designed for traditional RunCam and Mobius type openings. There are two top plates for this - one if the same size as the bottom plate for...
thingiverse
This is a friction fit mount for a RunCam Split Mini 2. It presses in through the back and fits snugly. The standoff size is 5.5 mm with a center-to-center distance of 30 mm, but when printed with TPU, it should work for standoffs between 28 and 32...
thingiverse
This is v2 of my first Runcam Split Mini Gimbal: https://www.thingiverse.com/thing:2917078 Fewer parts and made for a 180 degrees pan servo. ... I also made a v3 of it for 3-axis:https://www.thingiverse.com/thing:3138478 Video of it in action...
thingiverse
A quick mount I made up to mount the RunCam Spilt Mini on the nose of my X-UAV Mini Talon. ...The micro SD card is a bit fiddly to get out but otherwise its all good.
thingiverse
The casing holds the complete part of the "split" without camera and protect all the parts from water and dirt. ...In the next version there will be some air holes to keep the whole device cool.
thingiverse
This parts is Runcam Split mini holder for KINGKONG ET100.(material is TPU)
thingiverse
A mount for runcam split mini camera for ZOHD nano talon plane. ... It contains two parts - ring ant stand.
thingiverse
Bracket for RunCam Split Mini 2 to fit between 25mm mounting holes. ... Tested on an Ummagawd AcroBrat
thingiverse
So you can extend and retract a runcam split mini v2 from under the belly of a plane
thingiverse
This is V1 of my pan & tilt for the Runcam Split Mini. ... I also have a pod for the Mini Talon that this fits into.
thingiverse
Needed a 30.5mm stack mount for my 20mm Runcam Split Mini. ... Works great with R-XSR 30.5mm Mount: https://www.thingiverse.com/thing:2913821
thingiverse
This holds the runcam split mini 2 camera and its control board, in a model that can be screwed into place on the nose of the Ranger EX FPV plane from Volantex.
thingiverse
protecting my runcam split mini with a strong, crash proof protection against rough landings/crashes when battery can bump against the runcam board/camera. In the end I did not use the screw holes, as the board is already fixed by the foam. ...I do...
thingiverse
Simple way to mount an RunCam Split Mini v2 on top of the vertical stabilizer of an fixed wing aircraft. It has provisions for board placement, with ribbon cable coming out from the top. ... Image flip will be required on the camera, but buttons and...
thingiverse
This support is designed for the runcam split mini v2. It should be installed on a BetaFPV 75X. Main goal was to make it as light as possible. (<2gr) It is asymmetric so you can take the SDcard easily. v3 (<2gr) is light but weak. v4 (3.5gr) is...
thingiverse
_________________________ This is a simple 30° Mount for the Shrieker to use with a Runcam Split or Mini. I wanted to move the camera as far up as possible to reduce the amount of visible propellers in the image. Use M2x3mm screws (M2x4mm may...
thingiverse
This is a collection of parts that allow you to mount a RunCam Split Mini neatly into the nose of a NanoTalon with the ability to 'tilt' the camera. It includes a couple of parts to use as a cutting guide so that you can get a neat fit. The...
thingiverse
The threaded spacers that come with the split mini v1 are terrible for making a stack. Print two of these, slide them in from the side and you have a much nicer stack spacer. ...Be careful on the side of the solder pads, there's a small SMD component...
thingiverse
I FPV'd my Durafly Supermarine Spitfire Mk24 V2, and made a gimbal for my headtracking. I did the top in two part and glued it together. ... The mod movie: https://youtu.be/6fGKlODKnFM Camera: https://goo.gl/tpzjGM Servos: ...
grabcad
150er Copter with RunCam Split Mini and Tilt Gimbal