s&w 500 speedloader 3d models

Speedloader for S&W 65 and similar sized guns (K-Frame). Proto in test: https://youtu.be/zkJZYDQMoiQ Requires a 4mm machine bolt, a nut, and a washer. And a spring, one from a ball-tip pen will do fine. For holster, this fits the S&W 586...

.500 S&W Magnum: https://www.thingiverse.com/thing:4936608 .308 Winchester: https://www.thingiverse.com/thing:4935863 7.62x39: https://www.thingiverse.com/thing:4937156 5.56 NATO: https://www.thingiverse.com/thing:4935763 .45 ACP:...

A speedloader for S&W 586/686 revolvers, with holster. Requires two ball point pen springs and an M4 machine screw and nut. Also requires 2 M3 screws and nuts for the holster. The holster is designed for a belt no wider than 45mm. The holster...

This is my custom speedloader carrier, designed to fit a Safarland Comp I speedloader for a five-shot S&W J-Frame in .38 ACP on a 1.5" belt. This is my first atttempt at an OpenSCAD model, and while it is parametrized it's probably not as clean as...

Made for the S&W 627 Target Champion, old model (627-1) 6 shot, hole circle diameter 27.85 mm (For the non-metric people: 1.096") Model has to be scaled in size by +/- 0.1 or 0.2mm in total size depending on your printer, for a perfect fit. Please...

I needed a loading block big enough for the 500 S&W so i just designed this 25 case block. I also designed a high density version that has a smaller footprint. ...

Speedloader for S&W 17 and similar 6 shot .22LR revolvers. Required one ball point pen spring and one M4 machine screw and nut with one wide washer. ... This one works extremely well.

This is a speedloader block for easily loading Safariland speedloaders for your 5 shot smith and wesson j frame revolvers. It's a heavily modified version of someone else block, I forgot who's I tried looking for it but couldn't find it to give...

6x6 Loading Block works with .38SPL & .357Mag. ...It works with Safariland Speedloader, others not tested. Second Version is for Wadecutter. ... The Single Block you can use for testprinting.

Slimmed down and finetuned K-frame speedloader. Use a screw to assemble. Included is a holder. Use zipties for belt loops. Use velcro tape to add tension. Tested for 2 months at the range. EDIT 13-apr-2023: added a tighter lock (.2mm more...

This speed loader has a flat side which works out nicely for my S&W Airweight. So I wanted a holster for it to have a matching flat side to help maintain the orientation of the flat side since that side needs to face the gun when reloading. I also...

This is a smaller version of the 500 S&W Loading Block that I previously posted.

.500 S&W Magnum stacking loading block. ... This is a work in progress, so check for updates before printing.

It is based on the cylinder of a S&W 500. I didn't have all the exact dimensions so I guessed some of them. ...Looks pretty good and holds all sorts of pens and pencils.

Dummy round

Dummy round

.500 S&W Magnum Vase Mode stacking loading block. ... This is a work in progress, so check for updates before printing.

Finetuned, slimmed down customized version of the 5shot speedloader I found on thingiverse. Use a screw to assemble. Use velcro tape to tune tension. Included is an adapter for my own design 6shot K-frame holder. EDIT: added CUSTOM5 body...

Assembly instructions: Snap the hinges into the box bottom's hinge hoop making sure that the hinge tabs are fully engaged and locked in place. Flip the hinge tabs to the up position and place the box lid over the box bottom with the hinge hoops...

Assembly instructions: Snap the hinges into the box bottom's hinge hoop making sure that the hinge tabs are fully engaged and locked in place. Flip the hinge tabs to the up position and place the box lid over the box bottom with the hinge hoops...

This is a sturdier version of https://www.thingiverse.com/thing:5270385 or https://www.printables.com/model/187176-modular-ammo-box that is intended to better handle larger and heavier cartridges in high counts.Assembly instructions:Snap the hinges...

Speedloader für Luftgewehrmagazine, als Spritzgießteil.

Speedloader für Luftgewehrmagazine, als Spritzgießteil.

Assembly instructions: 1) Snap the hinges into the box bottom's hinge hoop making sure that the hinge tabs are fully engaged and locked in place. 2) Flip the hinge tabs to the up position and place the box lid over the box bottom with the hinge...

Assembly instructions: 1) Snap the hinges into the box bottom's hinge hoop making sure that the hinge tabs are fully engaged and locked in place. 2) Flip the hinge tabs to the up position and place the box lid over the box bottom with the hinge...

Assembly instructions: Snap the hinges into the box bottom's hinge hoop making sure that the hinge tabs are fully engaged and locked in place. Flip the hinge tabs to the up position and place the box lid over the box bottom with the hinge hoops...

This cover fits the S-500 power supply. This is a 12V, 40A 500W unit. It has switch and power socket mounting holes. My Power cord is the standard PC PSU power cord. The DC wires are simply brought out thru holes. There is a hole below the socket...

... until they lock into place. You may need to press the hinges into place in steps to keep the hinges aligned. 4) Slide the latch over the box top's latch pivot pin with the slot in the latch facing the box and the latch tilted inward 45 degrees.

Assembly instructions: 1) Snap the hinges into the box bottom's hinge hoop making sure that the hinge tabs are fully engaged and locked in place. 2) Flip the hinge tabs to the up position and place the box lid over the box bottom with the hinge...

Assembly instructions: 1) Snap the hinges into the box bottom's hinge hoop making sure that the hinge tabs are fully engaged and locked in place. 2) Flip the hinge tabs to the up position and place the box lid over the box bottom with the hinge...