s hook with clip 3d models
3018851 3d models found related to s hook with clip.thingiverse
... for it to work for your unique shelf thickness/dimensions. Things you can control: clip material thickness parameter shelf thickness parameter hook inside length hook depth inside length hook lip height -the lip that keeps cables inside the hook
cults3d
... design of a multipurpose hook. ...Enjoy it. Some of the uses I put it to: -Close packages -Organize hair bands -Holding curtain (in addition with a rubber band). And you, what use would you give it? ... You can resize it for whatever use you need.
cults3d
A hook that you can clip onto then end of a horizontal surface, such as a tabletop, bookshelf, etc. to hang things on. I'm using it for hanging a basket with filament on. I'm using Vik's Y-bearing holder to make sure that it can rotate (see...
youmagine
I put a loop of rope through the two holes that hang over this tabletop clip. Version 2.3 has some improvements, the hook's lowest point is now nearest to the table. A cord will tend to rest there causing minimum torque on the hook-clip. It is made...
thingiverse
A hook that you can clip onto then end of a horizontal surface, such as a tabletop, bookshelf, etc. to hang things on. I'm using it for hanging a basket with filament on. I'm using Vik's Y-bearing holder to make sure that it can rotate (see...
thingiverse
I wanted to be able to hang things (from the shower rod, on the door, over a chair, etc) with this clip so I added a hook. The normal clip half and spring are untouched from the original. ... ...
thingiverse
I added a hook to the original "light clip - polygon" model to catch the curled edge of the J-channel. ...This prevents the clip from sliding out if there is not much friction.
thingiverse
Clip-Hooks to hang thin clothes, fabric, ties, belts, paper etc. in a closed safely so they don't slip off. PLA is stabile enough. inspried by: https://www.thingiverse.com/thing:3748961 Insert an M4 nut in the clip and M4x16 screw in the knob. ...
prusaprinters
Clip-Hooks to hang thin clothes, fabric, ties, belts, paper etc. in a closed safely so they don't slip off. ...PLA is stabile enough. inspried by: https://www.thingiverse.com/thing:3748961 Insert an M4 nut in the clip and M4x16 screw in the knob. Print...
thingiverse
Thanks to RoboBaggins for his best design of clip. ... To assemble this clip, place the U-shaped part into one half of the clip , then sliding the other half of clip into it. ...
thingiverse
I was tired of all of my power cords flapping in the wind, so i designed this super simple little clip to hold the end of the cord to the previous loop. ... The Fit is just short of snug so it should fit a few different size cords, though i believe i...
thingiverse
I needed a hook which I could easily tie to a rope. Print Settings Printer: Wanhao Duplicator i3 Rafts: Doesn't...
thingiverse
Remixed to quickly add a cable clip to the original headphone hook
thingiverse
2/20/19 1230 Finally printed again with rafts at 20% Might change up the design a little and see if I can make it two pieces for additional hook sizes/ 05/15/2019 1315 added version four with a lightly larger hook to fit larger knobs but also...
prusaprinters
Can be used indoors as a wall hook or to manage cables.The hole diameter is approx 8mm , so any wall screw size 5-8 can be used to mount these clips.The clip can be printed without support, if its placed on one side as shown in the cura screenshot.I...
thingiverse
Hi, this is a remix of 2 different things: thing:793017 is the asker hook from Shetland57 thing:298955 is the clip from thomasforsyth I'd like to have a paper clip for recipes for my IKEA ASKER system. After printing I have to add a little foam...
thingiverse
I modified the original to add a hook so that I did not need to screw holes into my desk.
prusaprinters
I was tired of my other printed s hooks falling off my wire rack. ...These hug the wire rack a little tighter and therefore won't flop around as much when you go to hang stuff on 'em.the light duty works for hat weight items, heavy duty for most other...
prusaprinters
Simple S hook that is not too large or too small. I created honeycomb pattern in the body as an exercise in Fusion 360.</p><p>The wall thicknesses are small enough (1.2 to 1.6 mm) so that infill doesn't matter. ...Everything should be wall lines.</p>
thingiverse
I created this hook for hanging pots and pans in my pantry. ...I printed it at 80% because I thought it would be a little bit at full scale.
thingiverse
Same as ABS paperclip with utltility hook added. Now clip it and HANG it if you wish. ...Print Settings Rafts: Yes Supports: Yes Resolution: .27 Infill: 100% Notes: Same as Previous clip
prusaprinters
Battling the Corona! This door opener hook/elevator button presser can be held on a belt loop, for easy attaching and detaching. Print instructionsPrint with maximal perimeters, 100% infill and maximal layer thickness you can (I'm using 0.3mm), for...
thingiverse
... when not in use. *Update* April 10, 2020 = There is a new version of the Holster v2.1a that has a larger clearance for the belt clip. I have been using it at work for three weeks, as there is some two thousand people employed in the plant. ...
thingiverse
The snap hook doesn't have to be very strong because they are meant to rip free if hooked by a boat. When I sliced the original at half size to make them the size I wanted the hole was too small, I imported the file into freecad and enlarged the hole...
thingiverse
It is a little larger than I thought but it is the first print off my printer with new custom UN-official firmware. I had modded and made previous ones and they worked great but we just switch from 4 gallon to 8 gallon bags and one snapped, so I...
thingiverse
... from "willfly" works fine. ... I only had the problem, that the bracket slips out if something comes to it. So I added a small "hook" to fix the bracket/clip and hold in place. ... See original model text for print informations.