s13 rear subframe 3d models

The PL mount rear lens cap is designed with 4 protrusions shapes for easy hand grip. There is enough room in the rear to fit on other PL mount lenses. File sharing is for sharing ideas. Use it for personal use only. Commercial use is not...

The suspension ensures equal front and rear geometry, providing 5.6 degrees of camber at 1 inch vertical travel, 71% Ackerman steering, and a hub-to-hub distance of 1300mm. ...For the structural components, I used 6061 AL for uprights, bellcrank, and...

This is a rear sight based on the CR700W rear sight. This should easily fit on any 11mm dovetail rail. This should be a good addition to my PP700W front sight silencer adapter You will need a 1mm knurled pin to hold the blade mount onto the dovetail...

... stands at 100/90 R18. Both the tyres are tube type with the front tyre featuring disc brakes. On the other hand, the Honda Unicorn 160 tyres, which are tubeless, have got dimensions of 110/80 R17 tyre at the front and 80/100 R17 tyre at the rear.

I'm not sure what years would work, but I'm assuming if you have the rear shades, 2001-2006 probably works.Mine didn't print out super pretty, but I just like having the shade up and has been holding up perfectly. ...Print on its side so it doesn't...

... botvac, remove the two screws holding the drive wheels. Be careful not to lose the springs. From there, you can pop out the rear wheels from underneath and swap them. Once they are resting in place, you can assemble. Be careful of the wires! ...

Fit with the original SurRon rear light (use of SurRon original plastic screws and bolts to set it up on the moto). Need to dismount light plug, then mount it back once cable trough the support (easily done with a little screw driver) Shape on...

A small panel to fill the holes in the rear shock towers of an Axial Scx10iii. I used red as a contrasting color, but black would blend in and not be noticeable. There is a file for the front and rear, I just mirrored the set in Cura to get the...

This aftermarket Ohlins TTX rear shock is designed for the 1199 Panigale, excluding electronic damping valves (Ohlins ID: DU930). Constructed based on actual part measurements to ensure perfect interfaces. However, it does not include internal...

Although I have not yet had the opportunity to thoroughly test these rear hubs, I invite feedback from users who may identify areas where improvements can be made. ... Additionally, I offer 12mm hex adapters specifically designed for the Mini Inferno...

These parts are designed specifically for securing the rear brake line of the Honda XR650L in its correct position on the bike's rear swingarm. I've had my share of broken ones (no idea how it happened) and prefer not to invest in more fragile...

... a moldable state. Then, use this molded shape as a base for further technical printing in GF30-PP (XStrand). This modified cover can be used not only on Peugeot 107 models but also on Renault Clio vehicles with similar rear window wiper systems.

This particular design won't fit the 50mm lens, which demands a deeper rear lens cap - I've also uploaded a deep cap design, though. The file "MamiyaRearLensCapF.STL" was designed with a 0.5mm interference fit that turned out to be too tight after...

This rear sight is modeled after the CR700W rear sight, ensuring a seamless fit on any 11mm dovetail rail. It's designed to complement my PP700W front sight silencer adapter perfectly. To assemble this sight, you'll need a 1mm knurled pin to secure...

... are 2A or more. Update 2019-06-19: one of the feet broke off my original rear mount, so I have modified the design to have greater strength. The updated version needs two M4x20mm screws instead of the original M4x16. ... Category: 3D Printer Parts

... bike light mount to fit on a rear fender. ...You need to replace the screw that comes with the fender with longer one. The fit is pretty snug. The rear light in the photo is this one.Print with default orientation and a brim to avoid it from tipping.

... stands at 100/90 R18. Both the tyres are tube type with the front tyre featuring disc brakes. On the other hand, the Honda Unicorn 160 tyres, which are tubeless, have got dimensions of 110/80 R17 tyre at the front and 80/100 R17 tyre at the rear.

If you're interested in creating your own Rear Cap for Rapid Technology V3 Clamp, check out the customizer on Thingiverse at https://www.thingiverse.com/thing:3924676. ...Simply input the following parameters to get started: * INNER_DIAMETER = 73 *...

You can use it instead of the original ones to remove backlash and noises coming from the rear wheel. There are already a few versions of those bushings out there. I made a few changes to make them stronger and adapt them to the 3rd version of the...

In contrast, 1:10 cars offer a wider selection of shocks, but these typically feature longer rear shocks of around 100-120 mm, which is excessive for this model. ...To address this issue, I designed and printed risers that attach to the existing top...

For the "rear_left" I added some loops inside for zipties and filled 2 holes (since my ender does NOT have the 40x40 holes tapped). On rear_right, I filled the same 2 holes. For the front feet, I just cut off the "tab" he had to screw them into the...

... apart the vehicle as needed. My rear fin was printed using makerflex/ninjaflex for added durability, although any suitable material can be used. ...An updated version of the fin has since been added, featuring a shorter design and chamfered edges.

I aimed for a straightforward method to detach the PTFE tubes from the Prusa MMU2S's rear end. Having an effortless way to remove these tubes significantly simplifies the process of loading filament and clearing jams. The material used doesn't make a...

I'm revamping SummersideGuy's Veloster emblem with a bigger design that matches the Hyundai logo on the rear badge of the Gen 2 (2019 - 2020) Veloster. This remake can be printed in two colors by switching filaments at 2mm. ...I've got a whole makeover...

These models replace a broken cabinet drawer rear bracket with a sturdier part that keeps the rail from moving and dropping the drawer (smashing fingers). ... These parts are modeled from the original dimensionally, but thickened in the base section to...

A user-created model of this https://www.astroshop.eu/optical-finders/meade-8x50-rear-focus-viewfinder/p,47691viewfinder for Meade telescopes.The focuser mechanics are not included due to not being accesible to the user.Don't trust my threading...

Quick and minimal rear bracket to provide strain relief for something like a USB cable exiting your NABU. Uses a small zip tie and the stock screws after removing your blank cover. ... DesignSpark file is included if you want to modify it further.

I trashed my rear fin in a crash... so whipped up this alternative. I recommend my revised version here: https://www.thingiverse.com/thing:4763192 It generally just is better all round! If you like this design.. ...consider giving a tip:...

Rear dually wheel adaptor for the latest tractor models from Bruder (with removable wheels). This model is a mashup of https://www.thingiverse.com/hajdekr designs plus some CAD work to make it work for dually wheels. ...Here are the links to his...

A replacement for the Tamiya HotShot rear upper swing arm. Not a replica but a drop in replacement. Pivot holes are dimensioned at 3.2mm which gives a nice smooth fit with no play when manufactured with FDM. ...SLA and SLS could behave differently...