saab 9 3 jack points 3d models

Aux jack for Saab 9-3. ...Easy to print

Plastic seat adjustment switch in saab 9-3 driver seat, greetings.

Saab 9-3 in profile. Can be used as a keychain or hung in the rearview mirror. ...Just change the size.

These are the snap clips that help hold the rear spoiler down on certain NG900's/OG9-3's(1994-2002). The top portion is tricky on FDM machines and usually needs to be printed in at least 0.6 or finer. SLA printers should be able to make these easily....

It is the mating part of https://www.thingiverse.com/thing:221712 This fits my Saab 9-3 2003 convertible. It is similar to SAAB p/n 2381365. I recommend making this with ABS due to the heat of the lamp that inserts into it (press fit). This...

Saab 9-3 custom cupholder. ...Both cupholders in my 2007 Saab 9-3 worked well with the gear shifter and my water bottle. ...I designed this to fit in the plastic section next to the passenger seat opposite side of the handbrake.

This is a 3D-model I made using Fusion360 for my sister's Saab 9-3. I tested the knob myself, and it works like a charm! I know parts for Saabs can be a rarity, if not, expensive. ...So, I hope this knob can help someone who can't find it!

Корпус антенны для saab 9-3 (2G) Пару моментов по модели. Заполнения я ставил 0. Слои дна тоже 0. Стенки ставил, чтоб перекрывали всю модель внутри. Поддержки были включены. Высота слоя была 0.3 мм. ...Печатал отдельно с 9-ого слоя (сама антенна) и...

Saab 3d model. ...

This is my version of additional cupholder in central console for Saab 9-3 SS (2005-2010). https://www.eeuroparts.com/Parts/48578/Cup-Holder-Center-Console-12842692/ I didn't have an original part to make measurements but this one fits very...

... size. Print at 100% infill using a material that won't warp from sitting in a car. Originally designed for the Saab 9-3 & 9-5 F40 transmission. May work with F35 and F23 transmissions. ...Should also work in the Cobalt SS, Opel Vectra, etc.

The design is based on the SAAB 9-3 sportscombi but with a wide bodykit to fit the dimensions of the K989 chassis and a Hirsch inspired wing in the back. I modeled the body in blender with some 9-3 blueprints as a guide to get the dimensions of the...

This is a self-designed body for a WL-toys K989 rc car. The design is based on the SAAB 9-3 sportscombi but with a wide bodykit to fit the dimensions of the K989 chassis and a Hirsch inspired wing in the back. I modeled the body in blender with some...

Saab jack point cover. May not fit exactly, can be mirrored for opposite side (made so the readable text is the side it goes on). If I recall correctly it is for an aero. The actual part is no longer available. ... There is one of these out in the...

Saab jack point cover. May not fit exactly, can be mirrored for opposite side (made so the readable text is the side it goes on). If I recall correctly it is for an aero. The actual part is no longer available. ... There is one of these out in the...

Replacement clip for Saab 9-3 (02-)

saab 9-3 93 sedan family car sport swedisch, sweden,

Крышка для противотуманной фары для saab 9-3 2003 года

Saab 9-3 2001 Printable Car in separate parts

SAAB 9-3 Washer Fluid Reservoir Cap with Saab Logo. ... It needs 3 mm bolt and nut to assembly.

saab 9-3 93 sportcombi sport combi kombi estate wagon touring tuning family fast sweeden swedish

Saab 9-3 water pump holding tool, holding the gear in place when you replace the water pump.

Cookie cutter looking like a Saab 9-3(NG) key. The 4 buttons is supposed to make marks in the gingerbread! ... Merry christmas all Saabfans!!

Cookie cutter looking like a Saab 9-3(NG) key. The 4 buttons is supposed to make marks in the gingerbread! ... Merry christmas all Saabfans!!

This is a Iphone 6 holder that is designed to fit to the Saab 9-3 NG. It has holes cut out for the charging port, the 3.5mm headphone jack and the speaker. The holder is designed to work with a iPhone 6 with a thin TPU case. A plain iPhone will fit...

Designed an umbrella mount to be mounted on the two metal rings in the rear of the boot of a Saab 9-3. This was designed for a 2010 Saab however, will likely fit other models with these rings (see photos). I've added the Solidworks file also.

saab 9-3 (1998) car mod i made for cities skylines. it works, fine ingame. and it was fun to work on. ...http://steamcommunity.com/sharedfiles/filedetails/?id=1101681892

Saab 9-3 2001 Printable Body Car, with different wall thicknesses. ... All models are prepared to be printed on different scales, the model has several versions with different wall thicknesses to facilitate printing.

Adapter to install a DoubleDin head unit from Xtrons (TE706) in a Saab 9-3. The Xtrons has slightly different dimensions than a real DoubleDin. ...Do not print from PLA, it deforms at the temperatures that occur in a car.

This is the first piece of 4 complete set for CDC mounts, deaigned for Saab 9-3 OG ( 1998 - 2003). This part comes under left boot carpet to hold another element. ... If You have any questions feel fre to ask!