sainsmart relay 3d models
6537 3d models found related to sainsmart relay.thingiverse
This is an enclosure to house an outlet and a 4 input Sainsmart Relay. You can wire this up to a raspberry pi, and have Octoprint turn your printer on/off. ...This has supports for an outlet with threaded 6-32 screw holes and the relay is attached by...
thingiverse
This is a mounting board for the Sainsmart Dual Relay board (http://amzn.to/1gpfLMN). Note: since this can switch-line power beware and the reason I built it up a bit a left a plastic bottom on it for insulation. It also should go without saying...
pinshape
This is a case for the 8 Relays module for raspberry pi or Arduino from Sainsmart. ... There are enough holes for all cables and it can be adjusted wih 4 M3 screws.
thingiverse
This only allows access to the one side of the relay board as i have NO use for all 16 channels im only planning on using one full side at most. this is made to hold the arduino mega inside this thing: Arduino Mega 2560 Snug Case by Esquilo,...
thingiverse
Customized version of http://www.thingiverse.com/thing:261748 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=261748 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:77228 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=77228 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:351092 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=351092 Instructions Using the following options:...
thingiverse
a little box to hold the 4 channel sainsmart relay. I printed it with a raft, and supports for the slots... i put both the box and the lid side by side on one raft, and it printed nicely :) i used the default settings for standard print in...
prusaprinters
a little box to hold the 4 channel sainsmart relay. I printed it with a raft, and supports for the slots... i put both the box and the lid side by side on one raft, and it printed nicely :) i used the default settings for standard print in makerware....
thingiverse
This is just a coaster I made for the SainSmart 2-channel relay module. I made this coaster just to keep the module from shorting out on my metal workbench. I included mounting holes. Good luck getting screws to hold the module at the NC and NO...
grabcad
5VCD 2-Channel Relay board for use with Arduino and compatible controllers,
thingiverse
Created a enclosure for a SainSmart 16 Channel Relay Module. Used translucrent ABS for the top so you can see the leds shining through. ...Came out nice...enjoy printed at 0.25mm layer height
thingiverse
Built a box for the sainsmart 4 signal relay and huzzah 8266 board controlling it. Will probably be making some changes for ventilation and wifi signal passage. But trying this and if it works, will leave it. Putting it up in case it's useful to...
grabcad
Product page: http://www.amazon.com/SainSmart-16-Channel-Relay-Module-Arduino/dp/B0057OC66U
grabcad
Sainsmart 8 Channel DC 5V Relay Module http://www.sainsmart.com/8-channel-dc-5v-relay-module-for-arduino-pic-arm-dsp-avr-msp430-ttl-logic.html
thingiverse
This thing is a protection and mounting case for the popular 8-channel relay boards commonly sold under the SainSmart and Kootek names and by various eBay sellers. The opening in the top of the case helps dissipate heat generated by the relays. ...
thingiverse
Very simple snap-together case for Raspberry Pi 3 Model B and Sainsmart 2-channel relay board (https://www.sainsmart.com/products/2-channel-5v-relay-module). Boards are mounted using M2 screws, and a slot allows for wires to connect to the screw...
thingiverse
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/5hi8ZqEfoUW Turn the lid upside-down to print without support Support for case: Yes Support for Lid : No Not for commercial use! ...
grabcad
Cheap little USB 12V relay model I got from amazon. ...https://www.sainsmart.com/sainsmart-4-channel-12-v-usb-relay-board-module-controller-for-automation-robotics.html
thingiverse
Remixed to have a closed top. ...Ventilation might be an issue, use at own risk...
thingiverse
A case for a SainSmart 8-channel 12 V USB Relay Board Module. The board presses into the base and is clamped down by the top cover. The top cover is designed to be printed upside down with minimal supports inside the screw holes. The screw...
thingiverse
This is a case I designed for a brewpi build using the directions found at this website:http://www.homebrewtalk.com/f51/howto-make-brewpi-fermentation-controller-cheap-466106/ It is designed to mount an Arduino Uno, a SainSmart relay (linked to in...
thingiverse
This is a re-scale of clough42's 8-Ch SainSmart relay box to fit an Elegoo brand module purchased off Amazon. ... If you're unsure if your device can be used, the datasheet for the Elegoo shows dims between the screw holes: NE->NW: 128.4336mm ...
thingiverse
Enclousure for the 2-Channel SainSmart Relay Module. No Support needed. Printed on Hephestos 2 in black PLA with Buildtak. I used SketchUp to edit the original design. The SketchUp-File is included. After some users having problems with...