samsung bike mount 3d models
371474 3d models found related to samsung bike mount.thingiverse
Customized version of https://www.thingiverse.com/thing:614516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=614516
thingiverse
Very basic bike mount for the Samsung S9, the bracket and mount can be glued to together and the entire assembly is held to the bike frame using zip ties.
prusaprinters
Good luck. I needed a phone mount for my Radon Mountainbike so I decided to build it from scratch as a Fusion 360 training task. The pictures shows the first prototype printed in 0.30. The mount fits a Samsung S10 with TPU case perfectly. The...
thingiverse
The mount fits a Samsung S10 with TPU case perfectly. The attachment radius is 35mm. Top/bottom layer: 3 The clearance from the attachment to the mount is 10 mm. The screw size on the three screws on the phone mount part must not be longer than...
thingiverse
My 48V 11ah Samsung bike battery doesn't fit inside the frame, so I designed a bolt on bracket to go on the top bar. 2 x M5 bolts hold each 3D printed bracket onto the 40mm round frame then 2 more m5 bolts holds the bottom of the battery battery to...
thingiverse
Customized version of https://www.thingiverse.com/thing:426872 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=426872
thingiverse
A simple snap lock handle bar mount for your Samsung Galaxy A70. ... - Easy to print - No support needed - You will need 2 bigger zip ties I used some tiny felt gliders to prevent scratching the smartphones back on the handle bar mount.
thingiverse
Bike handlebar mount for Galaxy S5. Remixed to clean the model for better slicing and round the corners. I printed with bridge supports on and support angle set to 80 degrees to prevent supports from filling the beveled bottom edge. This fits well...
thingiverse
... the handlebar of my bike. ...It is meant to be attached on the vertical bar that holds the handlebar and it is made in two pieces which snap together. I've found out most bikes are slightly different, thus some adjustment may needed to adapt to yours.
thingiverse
Bike mount for Samsung Galaxy S8 Plus. ... 2x 3mm threaded screws and nuts for the support parts and 2x 3.5mm x 13mm self-driving screws for the case Hope you enjoy and please share your makes.
thingiverse
These are bicycle mounts for the Samsung SmartTag. The bottle cage designs work on standard frames (through-holes are 64mm apart from each other) If you are going to place a the bottle mount on top of this. I suggest you get a longer M5x20mm...
thingiverse
Well printed on wanhao duplicator i3 with 0.2mm layer height and no supports
thingiverse
Designed to hold a Samsung Note 4 in a Samsung phone case. Requires 4 #10-24 x 2 inch machine screws and nuts. Be careful to not over tighten if printed at low % infill. Printed in PLA at 15% infill for this first test print. It feels solid...
thingiverse
I remixed this mount http://www.thingiverse.com/thing:126820
thingiverse
It fits a Samsung Galaxy S8 with a Beetle phone case, which is pretty thick, so it might work with other thick cases like an Otterbox. You just need 4 zip ties to attach it to your bike's stem. ... Solidworks file added as well if you want to edit it....
thingiverse
A Remix of omikr0n's Smartwatch holder fitting for 42mm Smartwatches, especially for the Samsung galaxy watch. As a spring you can use an old ballpenn-spring, just cut it to ~5mm, for me this worked like a charm. I did one version for zipties,...
thingiverse
This is a handle bar mount for a Samsung Galaxy Tab Active2 on a road bike. ...It was created with FreeCad v19.
thingiverse
This version of my bike mount is designed to hold a Samsung Note 9 with Case. Rev. 2 Corrected counter sink and spacing of screw holes. Rev. 3 Added relief for Bixby button. ...Smaller latch for easier phone insert/removal.
grabcad
3d Printable solutions for the Samsung Smarttag and Smarttag Plus Bike Regards
thingiverse
Customized version of http://www.thingiverse.com/thing:912161 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=912161 Instructions Using the following options:...
thingiverse
I wanted it to record video from my bike or to follow the sat nav riding my motorbike. Please notice that you need a cover in order to fit the S8 properly. Without cover it could jump out from the place. If you want to modify the project, feel...
thingiverse
This is a Samsung Galaxy s Advance bike mount. This mount only works with a Gopro bike mount like this: https://www.thingiverse.com/thing:2338831 !!!!!Only works with a Case!!!!! ... Edit: Version 2 works without a Case
thingiverse
Customized version of http://www.thingiverse.com/thing:912161 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=912161
thingiverse
Customized version of https://www.thingiverse.com/thing:912161 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=912161
thingiverse
Customized version of https://www.thingiverse.com/thing:426872 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=426872
thingiverse
Customized version of https://www.thingiverse.com/thing:614516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=614516
thingiverse
Customized version of http://www.thingiverse.com/thing:426872 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=426872 Instructions Using the following options: width =...
thingiverse
Customized version of http://www.thingiverse.com/thing:2266715 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2266715