samsung nx min 3d models
33567 3d models found related to samsung nx min.cults3d
remixed from https://www.thingiverse.com/thing:4810566 https://www.thingiverse.com/thing:966948 just added a tube in between (just used the lower part of the nx part) and almost perfect... i dont have the skill in cad, nor the patience to twist them,...
thingiverse
remixed from https://www.thingiverse.com/thing:4810566 https://www.thingiverse.com/thing:966948 just added a tube in between (just used the lower part of the nx part) and almost perfect... i dont have the skill in cad, nor the patience to twist them,...
thingiverse
Samsung NX "Mini" Camera Cover. ... Reduced from Samsung NX to NX Mini. ...(diameter: 34.5mm)
cults3d
Adapter for using a Canon FD lens on a Samsung NX camera. ... Tested on samsung nx210 with canon fd 50mm
thingiverse
Rear lens cap for Samsung NX system. Sources included (Autodesk Fusion 360). ...
thingiverse
A simple adaptor from Samsung NX to 31.75 mm / 32 mm / 1.25" telescope eyepiece. ... Remixed from: https://www.thingiverse.com/thing:513379
thingiverse
A spare cap for your Samsung NX lenses. ...It is also deeper that standard ones, so it can also accept lenses like Samyang 12mm with a more protruding back element.
thingiverse
The flaps broke on my original Samsung NX-100 battery cover and the battery is not making a connection this way, so I designed this based on the original battery cover. ... It can be removed by bending the metal tab a bit in the middle and pulling off...
thingiverse
T2 adapter for Samsung NX "Mini" (diameter: 34.5mm) Reduced from Samsung NX to NX Mini. ... Short-circuit with pin 11, pin 2 or pin 9 and switch to manual mode.
thingiverse
Lens Cover/Guard for Samsung NX Mini camera with the 9mm lens
thingiverse
Battery door replacement latch for Samsung NX 30 cameras. ...To replace, cut off metal cover and glue it back afterwards.
thingiverse
Adapter to mount old M42 lenses to new Samsung NX cameras, while being able to tilt the lens by a few degrees. ...
thingiverse
This is an adapter to mount M42 lenses to Samsung NX cameras. It's cut in two pieces, so you dont need support. ... 11/01/14: complete redesign
thingiverse
#### English Here's a T2 adapter for Samsung NX cameras (diameter: 43mm; pitch: 0.75mm). ... Works very well for adapting your hybrid camera onto your telescope ;) I modified loco's adapter to change M43 thread to T2, add grip around the ring and...
thingiverse
... Pentax len's cover the sensors focal plane. i used this for the Pentax sidehttp://www.thingiverse.com/thing:15162 i used this for the samsung NX side.http://www.thingiverse.com/thing:429294 Hope this is usefull to someone and is work in progress.
thingiverse
Canon lens adapter for Samsung NX Mini cameras. ...(Extension: 20mm) Reduced from Samsung NX to NX Mini. ...(diameter: 34.5mm)
thingiverse
Mount adapter for using Nikon's F mount lens with Samsung NX mount camera body. Instructions Print the model with replicator with following settings. Object infill 100% Layer height ...
youmagine
This family of boxes holds up to 3 spare batteries, one SEF8A flash unit, and up to 3 SD cards, all used with Samsung NX series cameras. There are small bumps in each slot to keep the batteries, flash, and cards from falling out and similar bumps on...
prusaprinters
Quick remix changing the AF to E adapter to an AF to NX adapter. Removed 7,5 mm from body to change flange distance and changed E flange to NX Flange. Flange will need to be screwed in from inside of the main adaper part. Prints fine at 0.175 layer...
thingiverse
Removed 7,5 mm from body to change flange distance and changed E flange to NX Flange. Flange will need to be screwed in from inside of the main adaper part. Prints fine at 0.175 layer height. Some screws are a bit hard to get in. If you don't...