samsung phone dock 3d models
74755 3d models found related to samsung phone dock.thingiverse
Remixed so it can fit a Samsung S21 5G and changed the charging hole size so the standard Samsung USB C cable will fit.
thingiverse
Designed to fit a UGreen 90 degree USB-C cable https://www.amazon.com.au/UGREEN-Degree-Charging-Charger-Samsung/dp/B07P6QV9GB/ Instructions: Set up your slicer (I used PrusaSlicer) so that it only draws support material for the landscape base of the...
thingiverse
The height of the charging coil was specifically positioned for the Samsung Galaxy S22 (that's the phone pictured), but hopefully it works for other phones. It may be too high for shorter phones, in that case I could design some additional spacers...
thingiverse
This dock fits a Samsung S2 without a case. Supports phone and amplifies sound very well. Print Settings Rafts: No Supports: ...
thingiverse
Customized version of https://www.thingiverse.com/thing:4187296 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4187296
thingiverse
I made this dock for the Note 4. ...It uses the existing samsung charging cable and locks it into position. Just slide the phone in, and it connects with the micro usb connector every time.
thingiverse
The Samsung Dex Dock also has a limitation when using a case, but this one is smaller overall and with this extender, you can use it with your phone case on. At leasat a somewhat thin case. i am using a Spigen air case with mine. ...This will also give...
thingiverse
***************************************************************************** I had this trio charger, that i use to charge two phones, and got sad when i wake up in the morning and only 1 phone is charged, cause its missed lining up, i don't want...
thingiverse
car phone dock for volkswagen air fan mount, for samsung s4 including case don't make it in PLA ! ... had it in the car for one 1 day with a little sun and the phone doesn't fit anymore ;) Instructions printed on Ultimaker2 PLA 2x M4 x 50 bolt
thingiverse
Samsung Wireless Charging Dock for Samsung Phones and Samsung Galaxy Watch 3. Chargers used for this project, Samsung EP-P1100 phone charger, Samsung EP-OR825 watch charger. Used with the original usb cables. Samsung wireless phone charger is a...
thingiverse
Dock to fit in the EP-P1300 Wireless Charger from Samsung. Designed to fit my Samsung S21 Plus (with case). Angle of the dock is 45 degrees, so prints fine without support. ... There are 2 version, * V1: Original design *V2: Slightly refined...
pinshape
Dock to fit in the EP-P1300 Wireless Charger from Samsung. Designed to fit my Samsung S21 Plus (with case). Angle of the dock is 45 degrees, so prints fine without support. ... There are 2 versions: V1: Original design V2: Slightly refined design
thingiverse
Customized version of https://www.thingiverse.com/thing:2764188 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2764188
thingiverse
A wireless charging dock for mobile phone. two adapters for Samsung charging pad and a generic small charging pad. ...The Charger Model for Samsung is EP-PG9201 with an outer circumference of approximately 96mm
thingiverse
This dock fits a phone with a thin case and a 91mm charger. ...I used a Ram Mount to attach it.
thingiverse
Created this phone stand/ dock as I couldn't find a universal dock that I could use with a phone and case while charging. So I decided to make one! after about four design changes I ended up settling for this one! probably will keep tweaking this...
thingiverse
The Gear S3 charger is, I assume, only usable for the Samsung Gear S3 series watches, I'm not sure about newer or older Samsung watches or chargers. Charger is RavPower. Prints at 0.2mm layer height fine, but print at 0.1mm for better looks. ...
thingiverse
This is a remix of my remix of a wireless charging dock for a phone (anything Qi compatible) and a Gear S3 watch. Go to the original remix of mine for more info on compatible chargers. This Thing just has a modified appearance to it, which IMO...
thingiverse
I didn't want to waist too much PLA while printing this dock so i took out some parts. Works well for any devices, very strong! Print Settings Rafts: Doesn't Matter ...
thingiverse
I have a YouTube Channel with new 3D printing videos out every week check it out at http://www.YouTube.com/onlylittlemike Follow me on Facebook : @Makerground Follow me on Twitter: @Makerground3d This is a great dock that I designed in Solidworks...
thingiverse
Drew this up quickly in Fusion360. It easily holds a Note 9 with an Otterbox Symmetry case on it while charging. There is also a 14mm x 14mm slot for an earbud, but could also be used for a pen/pencil. It's well balanced and only took about 3...
thingiverse
I have a YouTube Channel with new 3D printing videos out every week check it out at http://www.YouTube.com/onlylittlemike Follow me on Facebook : @Makerground Follow me on Twitter: @Makerground3d Designed this part on Solidworks and works great! ... ...
thingiverse
This dock can hold several sorts of phones and tablets. It can hold a Samsung galaxy S2, a HTC one, a Samsung galaxy tablet 2 10.1 and an iPhone 4, 4s and 5. ...It may hold other sorts but i have only tested these.
thingiverse
Phone dock for your desk/bedside table. ...Fits all iPhones, even in most cases while charging.