samsung phone holder 3d models
369806 3d models found related to samsung phone holder.cults3d
... where to put them when we charge them. ...Here is a support studied for Samsung Galaxy A50 (2020) but it should be adaptable to other models. There is a place to plug in the cable and at the same time it allows you to secure the phone on its holder.
thingiverse
i made this to fit for my Samsung Galaxy S20 FE the hole at the bottom is for your cable easy but nice design just print it on the side
thingiverse
This is a charger/holder for Samsung phones with a rectangular plug. Version 2 doesn't have any cable management. Version 3 does have a tab for wrapping the excess cable. ...
prusaprinters
This is a charger/holder for Samsung phones with a rectangular plug. Version 2 doesn't have any cable management. ...Version 3 does have a tab for wrapping the excess cable. Print Settings Printer: Sovol SV01 Rafts: No Supports: No Resolution: 0.2mm...
thingiverse
This is a phone mount to mount a Samsung Galaxy S7 to the wall. I designed it to fit my phone with my case on, so it may not fit your phone. ...My case is a Spigen with a hard case.
cults3d
I changed the mount to use a threaded nut for a more secure hold. ... Need a M3x10 screw, nut and washer to assemble. Phone holder is designed to fit phone with Spigen case.
thingiverse
I changed the mount to use a threaded nut for a more secure hold. ... Need a M3x10 screw, nut and washer to assemble. Phone holder is designed to fit phone with Spigen case.
thingiverse
Many time you can't find table beside your phone charger to keep the phone over it meanwhile it is charging. Here, i designed 2 models, one compact and the other with wings to add more stability to the phone and to ensure not to fall off and may get...
cults3d
Many time you can't find table beside your phone charger to keep the phone over it meanwhile it is charging. Here, i designed 2 models, one compact and the other with wings to add more stability to the phone and to ensure not to fall off and may get...
pinshape
... in inventor and can be 3d printed. ...The width of the holder is 72 mm which makes the holder to keep the mobile in portrait or landscape mode. You can watch videos or can keep in charging by using this holder. ...The thickness of the holder is 3 mm.
thingiverse
my note 8 holder with gap for my magnetic charger lead on the bottom cable tie mounting point on the back and a amp cone and hidden channel for better sound
thingiverse
Customized version of https://www.thingiverse.com/thing:2771040 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2771040
thingiverse
Print Settings Printer brand: Creality Printer: CR-10 V2 Materials: PETG Temp settings: Buse = 240°C Bed = 80°C Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 30%
thingiverse
Customized version of http://www.thingiverse.com/thing:1665478 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1665478 Instructions Using the following options:...
thingiverse
Was having issues with other prints with my outlets, putting the phone on the holders would just push the charger out of the outlet. Designed this to be as close as to the wall as possible to help prevent the charger from being pushed out, as...
thingiverse
Replacement nut for a Samsung telephone holder with M22x1.5 thread and 17mm ball socket as shown on the pictures. ...Mine broke so I designed a new one.
thingiverse
For the cable, I'm using the following one : SUNGUY [2-Pack] 1M/3FT USB C Cable 90 Degree Right Angle USB-C Max 5V/2.4A 12W Fast Charging Data Sync Braided Cord for Samsung Galaxy S9 S8 Plus Note8, Sony Xperia XZ,Moto Z2 Force and More More...
thingiverse
Phone Holder for Samsung Galaxy S9 that mounts to both Fanatec CSL Elite & Clubsport Wheel bases for use as a dash. 55mm spacing on the M6 Countersunk cap screws. ...
thingiverse
I have printed it with ABS and has 100% infill, took about 11 hours for the bigger part.
thingiverse
Phone holder for samsung A20 with textile flip flop case, dimension of phone 150mmx15mmx cca 80mm. ...Designed to car CD slot in radio...In this picture there is the example in BMW car.
cults3d
... them off my bedside table into the trash can... ...(I barely rescued them last week) So, I decided to create a phone holder for my bedside table that will hold my phone, eyeglasses and the Samsung earbuds and allow the earbuds to be able to be charged.
thingiverse
A simple mobile phone charging station for Samsung Galaxy S7 (140 x 70 mm). ... The station has a canal for the USB charging wire.