samsung watch stand 3d models
240110 3d models found related to samsung watch stand.
thingiverse
just a quick remix of the apple version. ...I *think* the samsungs all use the same charger? it's a 34mm diameter block. ... easy print, no supports needed.
thingiverse
Smartwatch holder/ charging station for Samsung smartwatches. Use a thin double-sided tape to secure the charger into place or print it a few percent smaller to create a tight fit. No need for supports if printed like shown in the picture were...
thingiverse
Samsung Watch Charger Stand with/without Bracelet holder for Samsung EP-OR825 Charger or same size. ... 4pcs M5x16 ISO 4762/DIN 912 4pcs M5 NUT
thingiverse
I liked the Apple Watch 'Thing' stand, and the Samsung Watch stand fingers had lost a lot of detail. So... I combined the two. NOTE: The Blender mesh is incomplete! You will need to load this into Cura and run Extensions --> Mesh Tools --> Fix...
thingiverse
Samsung Watch 2 stand for charger, could possibly be used for others, the hole is 34mm by 9mm deep so if your charger is the same or smaller it should be ok. Print lying on side as in picture, no supports needed. ... Link to the filament i use...
thingiverse
This is a great design, I tilted it about 22 degrees, and added to the bottom a little.
thingiverse
q fossil charging stand with mickey mouse for samsung galaxy active 2 watch
thingiverse
Remix from Samsung Watch Charger Stand by Minglarn. I didn't like the 45 degree tilt for the charger so I made it flat so the watch could lay down on it to charge. ... This way it doesn't fall off when bumped...
cults3d
stand for samsung galaxy watch 4, with space for 34 mm diameter charging unit.
thingiverse
This is a remixed Samsung GearFit smart watch stand from a model I downloaded a couple years ago. (I can't find the model again now, but if anyone recognizes the shape of the stand comment it in and I'll add it in the attribution.) This prints in two...
thingiverse
Hey all I made this for my Wife as she liked my Samsung stand. ... There is nothing special about this stand but if you like it please show some love and leave a like ore a comment
thingiverse
A remix from the (https://www.thingiverse.com/thing:1980654) charger stand for Gear S3. Thought is was to wobbly so made the bottom a bit larger. Fits Galaxy Watch charger for S3 & S4. ... Also included a mirrored version.
cults3d
A remix from the (https://www.thingiverse.com/thing:1980654) charger stand for Gear S3. Thought is was to wobbly so made the bottom a bit larger. Fits Galaxy Watch charger for S3 & S4. ... Also included a mirrored version.
thingiverse
This is a remix from https://www.thingiverse.com/thing:4070274 I've extruded the watch part of the stand, since I only needed that one. I lowered the foot with 3mm in the slicer, since I didn't need that much height and width. ...
cults3d
Charging dock for all galaxy watch 4 and 5 models. ... On the back side there is a place for 10x10 mm magnet to hold charging "puck" in place.
thingiverse
Remix of the original with the charger USB wire going to the back of the stand rather than side. ... Infill: 25% Speed: 50 No support
thingiverse
This stand is compatible with all Samsung branded watches using the standard wireless charger that comes with the watch. Simply push fit the wireless charger into the stand, no glue required! To create the bottom rubber stands, use a hole punch on...
thingiverse
The original design was great, but I have had problems with the cable not staying in the cable pathway. This remix adds a few extrusions to the cable path to help hold the cable in place. ...
thingiverse
The same as the original, but with a wider base. ...I wasn't able to cleanly widen the base, I'm not that good, so sorry about that.
cults3d
Samsung Watch 3 Charger Stand I did not find something that suits me so I designed one
thingiverse
Easy to print charging stand that fits the magnetic charger for Samsung watch. ... Easily printed without support
thingiverse
An easy to print watch stand / charger that fits the magnetic charger for samsung galaxy watch and many more. There is a pocket at the topp for the charger. ...34mm.