scale rc driver 3d models

This is the stl for the RC truck driver 'Felipe' on my Etsy shop. I haven't printed this one myself yet. My models were outsourced to a commercial SLA printer. ...However, the build tolerances are well within the specifications of my Anycubic Photon.

Это ремикс Мне нужен был водитель в RC модель Я нарезал его, для удобства печати Уменьшить до 80% для rc это примерно 17 см Есть отдельные части и файл целиком Для соединения я использовал фидерную резину. ... если не открывается файл,надо...

rc scale wiper

Scale toolbox for your RC Garage.

Rc scale fuel cell 1/10 great scale part for your car

This is a small antena to add to your RC scale Cessna airmodel

scale car battery for your RC Car. ...Mainly for 1:10

Rc scale battery truck, a perfect fit to tamiya tractor or any other truck.

Just a simple pistol grip RC controller for your scale shop accessories. ... Scale accordingly to the size you need it.

Simple sandboard for RC Scale Crawler. ...Print Settings Printer: Geeetech Prusa I3 pro B Rafts: No ...

This is a reupload and rescaled version for 1/10th scale . ...this is a scale bucket seat for your rc cars or other scale needs. ...the seat can be rescaled pretty easily also

some scale liquid tank accessories for your R/C car. ...you can adjust the size and scale of this part in your slicer to make it the size you want for your rc car

a scale pylon that is stackable accessory for your R/C car. ...you can adjust the size and scale of this part in your slicer to make it the size you want for your rc car

Printing Instructions 1x Base (PWM Driver or RC Driver HAT edition) 1x Handle 2x Frame (for front and rear) 2x Screw for Handle (1.2mm walls) 4x Screw for Base (1.2mm walls) 4x Spacer (if needed for clip adjustment) Supported RC Cars Desert Monster...

## Printing Instructions * 1x Base (PWM Driver or RC Driver HAT edition) * 1x Handle * 2x Frame (for front and rear) * 2x Screw for Handle (1.2mm walls) * 4x Screw for Base (1.2mm walls) * 4x Spacer (if needed for clip adjustment) ## Supported RC...

you may need to change its size depending on the size of the RC vehicle your using (i made this 1/10 scale size so it will be good for 1/10)

cool design, 170mm tall 64mm wide. ...you can attach a hose for the perfect scale look, small grooved area for square clear screen to fit on the face. ... Instagram @majorscale.rc

this is a simple race driver for your formula 1 open rc car.. uses a m3 screw  to attach it threw the supplied hole in the cockpit.. ... minimal supports needed for the windshield and under the drivers chin.. 

scale

Antenna to RC planes, like BF-109 or A6M2. ...I hope you enjoy it.

This is a combination of Ossum's 1/10th jeep (scaled up a bit) and MrCrankyface's rc truck V3 drive line the only part i changed on the v3 truck parts is the diff case so use his files for everything but that All ossum's jeep parts have been scaled...

1:8 to 1:10 scale trailer for RC crawlers. I found the amazing offroad trailer by FarmersMark here on thingiverse. The design is great but I wanted a different look for my version. So I desided to make a remix. After a lot of hours I think I'm...

1:8 to 1:10 scale trailer for RC crawlers. I found the amazing offroad trailer by FarmersMark here on thingiverse. The design is great but I wanted a different look for my version. So I desided to make a remix. After a lot of hours I think I'm done...

This is a Driver for the open rc tractor. https://www.thingiverse.com/thing:1967086 I needed some extra space for the electronics I wanted to fit in the tractor (Speaker, soundmodule), so I came up with the idea of an hollow Driver. So here Comes...

sand ladder for scale crawler

Holds the 7 piece driver set that is commonly used in RC and other Hobbies on the IKEA Skadis pegboard. It is a remix of CSD_Salzburg's design. You will need to print the 2 hooks (Skadis_Universal_Hook.stl) to go with it these can be found @...

1:8 to 1:10 scale trailer for RC crawlers. I found the amazing offroad trailer by FarmersMark here on thingiverse. The design is great but I wanted a different look for my version. So I desided to make a remix. After a lot of hours I think I'm done...

a simple highlift for R/C scale vehicule . ...Scale 1/10

-Scale Cooler- It is approximately 1/18th scale as is. W25mm, L47.03mm, H30mm (total, body with lid on top). ... Scale it to your needs, no supports are needed.

Another Scale Motor, will need to be printed on Resin Printer. ...File includes Headers