schiit stack rack 3d models
59759 3d models found related to schiit stack rack.thingiverse
Schiit Stack Rack (3 High). Fits 3 components into one tight fitting stack. I printed in PLA+, 50% fill. ... I refined the design from https://www.thingiverse.com/thing:3779425 This is a friction fit but works really well with the factory...
thingiverse
Remixed from https://www.thingiverse.com/thing:4815977. It didn't fit on my printer, so I simply split the model into two separate pieces. That's it. ...
thingiverse
A modular surround that will allow you to stack your Schiit audio components on top of one another. I designed these specifically to place a Mani and a Sys side-by-side, with a Valhalla on top (pictured). The hole on the top is to save on filament...
thingiverse
Was looking for a way to stack my Schiit neatly on my desk, without having to tie them together or create a lot of extra bulk around them. There were a few options on here, but none of them really met my needs, or didn't fit quite as well as I...
thingiverse
Two frames for the Schiit stack to hold them on top of each other. ...Modeled snug so the frames should stay in place but results may vary.
thingiverse
Stack mount your Schiit minis. Replacing the factory cover screws with 4-40x1/2" thread perfectly into the Schiit frame. File was printed in PLA with 100% fill to give the tabs maximum strength. My print of the 3 high unit wanted to lift on one...
thingiverse
Important to note that this is made for the Schiit Stack with the [Introprose RCA connector](https://introprose.myshopify.com/products/rca-crossconnect-for-schiit-stack). This connector adds about 2mm height to the stack and separates the Magni and...
thingiverse
I modeled and printed this recently to neatly stack all my Schiit, and find a home for the Cthulhu power supply. It works great so far, came together nicely, and the weight of the PSU at the base gives the structure a great deal of stability. It's...
thingiverse
Just a simple remix to add a third to the stack.
thingiverse
This is a case for a Raspberry Pi 4 that matches the look of a Schiit Modi/Magni.
thingiverse
https://www.thingiverse.com/thing:2187350 Nice, simple little rack. Lots of open space for air flow and cables. I've got my Pi 4 and Pi 2 mounted to the wall of my RV temporarily. I added two mount pins to fit an RPi 2B. Now I just clip off...
thingiverse
A Rapsberry Pi 4 case that matches my Schiit stack. This version has a small OLED screen. ... You will need right angle connectors available from Amazon at: https://www.amazon.com/dp/B06W56VLLY https://www.amazon.com/dp/B01N1EO495 OLED...
prusaprinters
... allows you to paint and stack doors & trim with ease. ...Now a contractor or homeowner can create a controlled environment in one area of a room. Get more done in less time and less space.Inspired by the ‘Stack Rack’https://www.stakracks.com/Enjoy
prusaprinters
Had to realign your stack of Schiit? If you're like me the rubber on the bottom of your Schiits always gets dusty and looses its firm grip. I got fed up with this Schiit Problem. The Schiit Bracket was designed with hundreds of minutes of R&D...
cults3d
Had to realign your stack of Schiit? If you're like me the rubber on the bottom of your Schiits always gets dusty and looses its firm grip. I got fed up with this Schiit Problem. The Schiit Bracket was designed with hundreds of minutes of R&D with...
thingiverse
Had to realign your stack of Schiit? If you're like me the rubber on the bottom of your Schiits always gets dusty and looses its firm grip. I got fed up with this Schiit Problem. The Schiit Bracket was designed with hundreds of minutes of R&D with...
thingiverse
I couldn't really find any racks on thingiverse that either stacked vertically, or had the game labels facing out rather than the front. This is the first thing I've designed to be printed, so any feedback in the comments would be great. This fits...
cults3d
A drying rack for cookies that is stackable 6cm high 30cm X 30cm
thingiverse
hice una revisión del modelo: https://www.thingiverse.com/thing:4441076, lo afine un poco para que calcen los tornillos comunes de HDD 3.5", le adose un soporte para que queden con pies el rack y además lo hice para 6 discos. ...
thingiverse
hard disk drive stack you will need 4pcs thumbscrew for each hard drive how to align loosely screw 2 drives on each other... tighten while on top of each other 3rd hard drive.. you can just tighten on an aligned drive. 2 files available.. in my...
thingiverse
In both cases the dowels should be opposite each other on the short side (see pictures for correct orientation.) After this is all over and the face shields aren't required anymore, lay the rack version on it's side and you can use it as filament...
thingiverse
Sideways holster for a Schiit Magni and Modi combo angled upwards 25° Made to be printed text-down
thingiverse
Kaleun96's under desk mount is a great design, however my Schitt Magni/Modi have standard OEM rubber feet. I removed 2mm of height from the bracket. ...Working flawlessly with my Magni/Modi 2 :) Many thanks to Kaleun96.
thingiverse
Glock 9mm Double stack version of my stacking magazine series. ...Simply slide the rack in from the side on the lower rack to stack them up and lock them together.
thingiverse
This design was made to fit the narrow plastic shelf in my stack-on gun cabinet but should work in any cabinet or safe. ...After printing I glued in some foam in the spaces for the butt of the gun to keep them from potentially slipping and also to help...
thingiverse
I needed to save some space in my kitchen rack by stacking my plates. But this came with the compromise of stacking my regular plates on the soup plates. So every time soup plates need to be deployed the regular plates needed to be moved first. Urgs....
prusaprinters
My lite cheap version of Saker Paint Racks Saker 4 in 1 painters accessory toolv1 -45mmv2 - 16/22/25/45mmOriginal Saker rack 255x145x29mm (see attached picture) but I resize it to 200mm
thingiverse
... my previous design, it still has the lowered height but this time I've reduced the amount of FLA needed to print. ...It's smaller but more effective *Update 11/09/19* Reworked the 8 and 16 stackable racks, it is now flat and removed the random piece.