scion xb modifications 3d models

SILENCE! is a guide for lowering the noise level in your QIDI X-Max printer using high quality fans and noise reducing foam. First of all, one of the noisiest components in your printer is the small and high pitched 30 mm extruder fan. I won't cover...

Initially, I encountered issues when printing ABS using a QU-BD extruder on my Hadron Ordbot. The problem occurred during large model prints with long run times, resulting in feed failures after a couple of hours. Research showed that this was a...

<p>Author : Volan</p><p>Link : https://www.printables.com/model/10929-70w-dimmable-led-worklight-v14</p><p>Minor changes :</p><ul><li>I replaced the square nuts for fixing the bezel with hot inserts.</li><li>I’ve reduced the housing for the square...

To adopt any linear rails combination, you can use these parts to mount Z-Axis linear rods and lead screw using KP08 bearing.

A selection of straightforward 5 car models, each consisting of 5 individual components - bodywork and 4 wheels, with unique pivot points for every wheel. Models are crafted from shared materials (excluding bodywork paint), making it effortless to...

The original file https://www.thingiverse.com/thing:3541540 claimed it wouldn't work with dual fan duct versions for the Hero Me. So, I decided to remix the design. I added reliefs on all four sides to enable mounting in any direction and ensure...

I removed slots and breakout tabs from the face of the lid and added 10mm round holes for ventilation on what will be the bottom side of my VESA mounted RetroPie setup. I fixed some messed up spots on the fan clips, possibly caused by importing it...

They needed a simple way to use an existing extruder kit with their Rostock Delta printer. This would separate the hotend from the stepper drive with just two printed parts. Those parts were made on an UP Mini using .25mm layer thickness.

These are the additional panels required to modify the Pimoroni Picade cabinet for a RC2014 computer kit. This should be laser cut from 3mm acrylic, plywood or MDF. The backplane mounting panel has mounting holes for either the Backplane 8 or...

This innovative face mask can be easily customized to combat coronavirus, while also allowing users to modify it to suit their needs. The base of the mask is printed at a thickness of 0.3mm, providing a sturdy foundation for further printing. Upon...

Набір для сборки форми для приготування традіційної сирної паски на Великдень, має хрестик та ХВ (Христос Воскрес) на поверхні, то буде гарно виглядати на свято! Як зробимо саму паску, відразу викладемо фото. Друкуйте по 2шт кожного типу, сбирайте,...

Pastry professionals rave about this high-end cookie cutter, featuring a cutting-edge surface designed for precise shapes. Industry experts rigorously tested it to ensure its durability and performance in the toughest baking conditions. ...Not only does...

I designed and crafted this cap to effectively seal the hole in the sound changer tube on the passenger side. This custom part boasts impressive dimensions, measuring 26 mm in diameter by 10 mm in height, making it sleek and compact. ...As a prototype,...

A Collection of Custom Keychains Made for TPU Filament Enthusiasts. Each Design is Named After the Real-Life Vehicle it Imitates, Ensuring an Unmistakable Connection to its Inspiration. ... For Personal Use Only!

About Car

I've put a few thousand miles on my MaXpeedingRod coilovers and they've held up great except for the rubber bushings on the rear. It may be in part to using my TB Performance rear strut bar. Either way, they were too soft and needed replacing. I...

Door Stoppers Repair Kit for Lexus RX300 (U10) A high-quality repair kit designed specifically for the door stoppers on your Lexus RX300 (U10). ...This comprehensive kit includes all the necessary components to fix damaged or worn-out door stoppers,...

I lost one of the washers in my Spec D Headlight when I was replacing the bulb and they can't be bought separately so I thought, hey, why not laser cut it out of acrylic? So I took measurements on the ones that I had so that I could cut as many of...

Factory reverse camera from Toyota Prius 3+. Disassemble and use only the sensor itself (lens part). In the middle of the printed element there is a small channel for cable management. ...If the printout is of poor quality, the thread for the grommet...

I just ordered one of these gauge pods for $25, and they came in at $2.99 with free shipping from Taiwan, which got me thinking - why pay that much when you can have it today for two bucks? I designed this gauge to fit the factory air vent on the...

I've modified the Mazda paddles, blending my own style with their design. After tweaking the file and five unsuccessful attempts, I decided to keep what I had because it fits perfectly. It even snaps into place smoothly. I'd appreciate it if someone...

This was designed for the 3" K&N Apollo's flexible duct hose, but should work with other hoses as well. It will help keep the hose from moving around as well as prevent it from rubbing on the underside of the wiring harness going to the fuse box. ...

Cooling Fan Bracket: I found the bracket on morganlowe's original to be too close to the 5015 fan and I was worried about it obstructing airflow, so I made this edited version of the cooling fan mounting bracket. The dimensions are the same except...

I have successfully redesigned the fan to dynamically adjust the blade pitch angle during simultaneous rotation, utilizing an epicyclic gear train. As clearly demonstrated in the video animation (assem 6.avi), the original design of the fan was based...

I designed this after seeing https://www.thingiverse.com/thing:3905354 which requires cutting into the controller's shell and doing irreversible damage. My controller is nearly a decade old and I don't really want to damage it, as it still works...

BACKGROUNDThis was something I actually designed almost half a year ago now, but never put up until today. I just finally sold my Blackfoot after not working on it for a while, so I thought I'd put this up before I inevitably forget to. As much fun...

Remixed from Ender3D's "Betray at House on the Hill - Organizer (& Baldur's Gate)" https://www.thingiverse.com/thing:3577659 or "on Cults3D" https://cults3d.com/en/3d-model/game/betrayal-at-house-on-the-hill-organizer-baldur-s-gate I modified the...

This is what I used to put the Maker's Tool Works leadscrews and anti-binding X-ends on my Mendelmax. I liked the anti-binding X-end design because I'd been struggling with Z-binding for a while. My Z motion is now silky smooth! The current...

I required extra shelves for this budget-friendly adjustable desk (approximately $40 on eBay). Similar shelves can be found at Menards for about $5 each. This design prints out brackets that slide over the existing support and do not obstruct...

Upgrading from the original Sovol parts cooling fan to a back mounted solution using a 5015 fan (or even the stock 4014) enables you to finally see what the print head/nozzle is doing since the fan assembly is no longer in the...