scope cover 3d models

Customized version of https://www.thingiverse.com/thing:3235246 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3235246

12V16.5A switching power Supply 100mm x 42mm

This is my first shared file so dont think its the best, but its the only one out here. My skills in 3d modelling is not the best therefore i attached the .obj file, so you can edit it yourself. ... For me it was fitting well.

Rear SCX10 and SCX10 II chassis rail plate. Attached by two crews into the rear chassis brace. will will need to drill a pilot hole on each side. This was created for my SCX10 II JK Wrangler hard body with a 3D Printed rear bumper. ...but will bit...

This is a remix of bertmag's Fallout Endstop. ...I used a skull and crossbones that I found on Thingiverse, sorry but I don't remember the original file or who to give credit to.

This is a replacement gantry x-axis mount. Make sure to rotate the part before slicing ---> upside down I copied it as precisely as possible. feel free to use it for your own remix. if there is a demand for the .f3d file. ... then I add it.

Scale: 1/35 Highly quality scale model detail set. SLA printer required. ... © Faustus Models 2022

<p>The original object does not have a flat surface on the back, plus I prefer a larger opening.</p><p>Inserting the remote is very difficult, because the original file... ...but it fit.<br>I just cut a slice on the bottom and a larger hole on the top...

My very first work. Those are 2 boxes. both 50/105/190mm, one side open One (with round hole) is for electronics with round movement sensor One is for power supply. Edges / corners are specially rounded a bit. Both are printed about 12h and...

Use with a brand new "Fire 7" tablet and the original protective case. Allow using usb charger. Mount with 3 small screws (V2). Print verticaly w/o supports V2 : New version - lighter; tougher! Print standing up, flat plane on the bed. ... Will...

Customized version of https://www.thingiverse.com/thing:2561342 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2561342

The model is in 1/35 and can be scaled to different scales. ... created by MA Models 3D

Remix to fit nicely 12 discs.

My remix version. ...I added Clips to the side and embossed my name

OBO Bettermann cable duct 110x70mm

For use with fan 4020 and TMC2209

This is a remix of https://www.thingiverse.com/thing:4639095 I've removed the elegoo logo for easier and faster printing and made the edges slightly smoother. This is only the version WITH the cutouts. Thank you to the original creator. ...

M4x16 bolt 2 PCs, M4 nut 2 PCs and M3x10 screw 2 PCs. ...Stainless steel.

Customized version of https://www.thingiverse.com/thing:767845 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=767845

I remixed this design with an extra height of about 4m to give the Notcua 80x25mm fan better fitting room. ...I also removed the buck converter mount because it is not needed with the Noctua fan.

<p>In my RR V-Core 3, I positioned mains-powered components in the lower part. While Wago 221 connectors are quite well protected against accidental touch, it is not the case of the power supply and the solid state relay. ...I have therefore designed a...

Customized version of https://www.thingiverse.com/thing:2561342 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2561342

Customized version of https://www.thingiverse.com/thing:2561342 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2561342

Print at 102-104% scale, remade using McBane's design dimensions. Added geared look to top for style. ...Heat up the top with a torch for easier installation.

Got a new printer so I need some fresh air without much fuss. So here is a bracket to with an 8" PC case fan with cable ties at each end to hold the duct. ...

The front panel of the box for the MELZI belonging to the TronXY X1. ... 2 Variants: single piece & Split into a TronXY X1 printable set of two with a 30mm overlap and grooves for the glue

super motor protector for TBS source one frame

7inch HDMI LCD (H), 1024x600, IPS, supports various systems, capacitive touch, supports Raspberry Pi 4. looks good and protected. ... Display link to Buy: ...

A couple years ago, we did a "radio play" onstage. We wanted to disguise our new, fancy mice to look like retro old mics. I designed and printed this to clip onto a neumann km 184. ...It's wildly specific but maybe it's exactly what you're looking for!

Covertor para tanque Grip: https://www.thingiverse.com/thing:1247597 https://www.thingiverse.com/thing:2623180