scope riser rail 3d models

Gaggia Classic Tank Riser (WIP) For 160 mm clearance

Picatinny Red dot riser. ...Requires M5 nut and bolt

2cm height figure riser (10cm diam. ...base) and back wall

A monitor riser for elevating a Series 6 Samsung TV.

Riser wall and first traingles row for geodesic dome #goodkarma888

Just a riser for some generic dollar store cat dishes.

13mm cheek riser for cz455 with boyds thumbhole stock.

This is an assortment of slanted risers for the modwing. ...I find that it lessens the need for a holster wedge. There are two 6mm risers and two 10mm risers. ...The raised risers are if you need a bigger claw

Bike Trainer Riser for 700x23c tire. ... 1.75" of lift.

Riser feet = ~33mm (with voxelab aquila original gasket ~37mm)

Someone asked for the Picatinny mount version of a Nerf Vortex Nitron scope that someone originally designed for Nerf rails. I remixed the original part to fit a Picatinny rail. Secures with a 10-32 x 1" screw and a 10-32 x 5/16 nut (McMaster in...

# English ## Description Picattiny/weaver riser for airsoft red dot sights. Adds 19mm height to rail. Two risers - 35 and 45 mm length. ## Additional parts You will need M4 nut and M4x27 screw (you can shorten M4x30). ## Printing instructions...

for 50 mm scope

... screws with countersunk heads and nuts. You might be surprised that the rail is actually 13mm, but this works better for me because it leaves a bit of wiggle room and my scope feels solid as a rock once the mounting screws are tightened down tight.

Gopro hero 5 scope mount for 48mm scope

Guide scope bahtinov mask (Altair MG32 Mini Guide Scope)

... adding TPU or a similar material underneath. Ultimately, these holes enable users to modify the riser's height by creating a male-female connection through a slight taper in the opposite direction, allowing for future adjustments as needed.

###45mm Width Risers * VER008S (PCE164P-NO6) * VER009S (PCE164P-NO8) ###43mm Width Risers * VER 006C (PCE164P-NO3) * VER 007 (PCE164P-NO7) Instructions: Take off the foam backing of the riser and slide it into the slot. ... Add GPU to riser like...

We've designed a monitor laptop riser within A360. ...Once fully built, this riser measures out to be 280mm long, 150mm wide, and 127mm tall.

Riser for cheap probe contact plate with an od of 35 mm. ... The od of the riser is 36 mm so there is enough clearence to fit well.

Stack Risers- ASR Series as per NAAMS StandardNAAMS: https://www.naamsstandards.org/Stack Risers: https://www.naamsstandards.org/Standards/chapters/assembly/E.pdfPage: E-12, E-13

Half the size as my larger Pot Riser! ...4" x 1.5" Plant Pot Riser Twitch.tv/TheBudLabCA, You asked for it!

A simple bed riser for post type bed frame feet on carpeted floors.

Riser for horizontal positioning for Xbox Series X for better heat dissipation.

center channel Riser Original model at thangs.com: https://social.thangs.com/m/852172

Building a High-Performance Wall-Mounted PC with a Custom GPU Riser

This is a half inch riser for a longboard. ...Print this laying down.

The Micro T1's riser block is a vital component of its overall architecture.

a simple riser to lift a 110mm cat bowl off the ground

This is a 3D riser model for a CFD tutorial design, available on youtube.