screw tightener 3d models
272508 3d models found related to screw tightener.thingiverse
... will only work with the long screws and not the short ones on the GoPro Hero series. However, the tool may work on the GoPro Session series as it is smaller. Check out my other GoPro screw tightener here: https://www.thingiverse.com/thing:2451934
cults3d
I find this design easier to use than my other screw tightener I designed. This tool works great on tightening and loosening the screws on your GoPro much easier than by hand. Unfortunately, it will only work with the long screws and not the short...
thingiverse
... Other compatible things: - [Screw](http://www.thingiverse.com/thing:999626) - [Bolt](http://www.thingiverse.com/thing:999651) ## Changes * Added a version with 1mm spacing. ...The old one has 0.5mm spacing between the tool and the screw.
thingiverse
... but this is more sturdy and solid. This will fit on a shelf or desktop up to 1 1/2 inches thick. I did have problems using Simplify3d slicing the screw. It kept breaking where the screw met the handle. ... I did not have this problem using Cura.
thingiverse
This is a tool to tighten the screws of the GoPro mounts. I printed this in ABS with 4 top and bottom layers, and 4 sidewalls. ...Infill 25%.
thingiverse
The original one was way too big for the screw heads I had, I had to rescale it so I decided to make a remix including a hole to attach a leash. ...For me everything needs a leash otherwise I just lose them...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/dTuj0Rk89yi
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/epR2vEwvPOP
thingiverse
mic boom arm screw with extra side base and screw tightener
thingiverse
I re-mixed the GoPro Max Lens removal tool to fit the regular hero 9/10 lens on the backside so you can remove both easily. ...I also added a GoPro screw tightener on the other end as well.
thingiverse
Remixed version of E3D v5 cooler and filament cooler with blowing angle ajustment
thingiverse
materials: two 5x15 metric allen screws an allen 5x55 metric screw three metric nuts 5 the model is not tested, please comment if the measurements are correct. materiales: dos tornillos allen metrica 5x15 un tornillo allen metrica 5x55 tres...
thingiverse
Replacement Part for Umbrella Stand which holds umbrella by screwing a plastic part down and compressing it against the pole of the umbrella. The original part broke (last picture) and after not being able to find a suitable replacement i decided to...
thingiverse
This is a fishing reel handle tightening screw cap. One of my friend had broken cap for tightening his fishing reel handle so I created the replacement. ...This is screw cap for oval head screw, the first one I saw in my life.
thingiverse
The tightening knob for my neewer fluid head stripped. ...This is a replacement that uses the original screw and spring to keep it "spring loaded".
prusaprinters
It is tight enough to screw only for a few threads, as it only needs to hold the joint inside.
cults3d
Exclusive to Cults Designed to fit a 21mm diameter curtain rail (printed at 100%) with a tightening adjuster, this will tighten down to a 12mm (1/2 inch) diameter rail. A ball design and for the prototype I've printed this in black PLA although this...
thingiverse
... M2 Tool Holder by 3DPrinterHowTo that also hosts the z-axis bolt driver plus counter nut tightener. Look for "MakerGear M2 Tool Holder (z-axis screw driver support)" Instructions Slice it with support structures using the alignment in the file.
thingiverse
This is simple tool which fits over my lab equipment terminals (which are sloped) and provides for a 'press fit' so that you can then turn the terminals with ease and get more torque on them to tighten them. ... Dimensions (in case you need to...
thingiverse
Tightening knob for printable screw from https://www.thingiverse.com/thing:5445853 For original screw use this: https://www.thingiverse.com/thing:4635007
thingiverse
I created this to secure two Foamcore (gatorboard) walls together that were only held 6" apart with velcro'd crossbeams for a POP display. ...These add rigid structure, and can also be used to pass cords through, - in my case we're passing 12v LED power...
thingiverse
A screw controled tightening system for the Tronxy X1's sometimes wobbly y-bed. I did previously use the model from PB2000 https://www.thingiverse.com/thing:2203872 , but either i was doing something dumb, or my matrial wasn't good enough; the...
thingiverse
... use hot iron or glue to fix one of the sliders in place(doesn't matter which one) so it does not slide one way or another. Only one of the sliders should be free to move(with some force). Then insert the screw and tighten the belt as you see fit.
thingiverse
... 3d printer. ...you put it in the top holes on the forward-most part of the frame. you should use 1 extra screw but the existing tightener has the rest of the parts. you might need to sand this to make it fit. just tighten the screw to tighten the belt.