screwdriver rack 3d models
40013 3d models found related to screwdriver rack.thingiverse
This is an 11 piece screwdriver rack I designed to organise my toolbox. ... I printed the part using eSun PLA+.
prusaprinters
Screwdriver rack designed to hold multiple sizes of screwdriver in any of the four spots. ... Also has mounts for a set of jewelers screwdrivers.
thingiverse
4-position screwdriver rack that securely holds multiple screwdriver sizes in any of the slots, rather than having multiple holes sized for a specific screwdriver. Also holds a set of jewelers screwdrivers. ... No supports, prints in 3.5 hours
thingiverse
Under-shelf mounting bracket for screwdrivers. Mount rail has universal mount holes with 22 and 44 mm spacing so that wider and narrower brackets can be mounted. ...I bought these screwdrivers on ebay.
prusaprinters
This is a compact rack for the Mastercraft Insulated Precision Screwdriversset (6 pieces) (#057-3604-2)No support is needed if printed on its side.This object main web page is:http://www.ctheroux.com/insulated-precision-screwdriver-rack/.You can...
prusaprinters
This is a compact rack for the Mastercraft Insulated Screwdrivers set (8pieces) (#057-3695-4)No support is needed if printed on its side.This object main web page is:http://www.ctheroux.com/insulated-screwdriver-rack/.You can request the source files...
thingiverse
... Insulated Screwdrivers set (8 pieces) (#057-3695-4) No support is needed if printed on its side. ... This object main web page is: http://www.ctheroux.com/insulated-screwdriver-rack/. ... You can request the source files on the page listed above.
thingiverse
... Set. ...It takes less space the supplied one. If printed on the side, no support is needed. This object main web page is: http://www.ctheroux.com/wera-electronics-screwdriver-rack/. ... You can request the source files on the page listed above.
prusaprinters
https://paypal.me/radicalreelAllen key screwdriver rackLink to the handle: https://www.printables.com/model/221894-ultimate-allenhex-key-screwdriver-rotating-end-cap
prusaprinters
This is a very simple screwdriver rack for IKEA Skadis pegboard. It requires two of my <a href="https://www.prusaprinters.org/prints/119811-skadis-universal-peg">universal peg plates</a>. ...I designed the rack for the small Mastercraft screwdrivers I...
prusaprinters
A customizable gridfinity compatible screwdriver rack.This is a bit of a work in progress. It's meant to be printed in multiple parts to avoid having to use supports. The four legs are attached to the matching holes in the top and bottom parts.The...
thingiverse
Small wall mounted rack I made for a mini screwdriver set I got from Amazon.
thingiverse
Simple screw driver rack for the Best Choice 9-Piece Precision Screwdriver Set | Phillips, Flat and Torx Star from Amazon.
thingiverse
It was designed for the pictured screwdrivers having 10mm barrels, and 15mm finger swivels, with a set of retainer knobs to keep them from vibrating off the rack when the music is jammin'. ... It has two countersunk mounting holes for small flat-head...
thingiverse
Bought some new screwdrivers and the old rack was not able to hold them. Every single rack holds up to 7 srewdrivers (holes for them have diameter 10 mm), and every connected one adds 8 ports. Connect them with an M5 screw/nut and they will be tight...
thingiverse
Just a basic rack to screw to a wall or the edge of a work bench to hold allen wrenches and screwdrivers. The small holes are 7.5mm dia. and have tubes extending below the shelf in order to allow a 6mm or smaller allen wrench to be dropped into the...
thingiverse
Rack to hang Wiha Soft Finish screwdrivers - I have a set of 12: 3 flat - 3.5, 4 & 6.5 2 Pozi - PZ1, PZ2 3 Philips - PH1, PH2, PH3 4 Torx - T15, T20, T25, T30 Sized for these, in that order. The rack is in two parts to accommodate it on the print...
prusaprinters
A nice Modular Mini screwdriver, 4bits,extension storage rack I designed with a Honeycomb Inlay that looks great. The End pieces are slotted and have 2 screw holes each for stability. These allow you to easily remove the Main rack if you...
thingiverse
A nice Modular Mini screwdriver, 4bits,extension storage rack I designed with a Honeycomb Inlay that looks great. The End pieces are slotted and have 2 screw holes each for stability. These allow you to easily remove the Main rack if you need to...
thingiverse
Holder for 18 Wiha PicoFinish screwdrivers (other brands or sizes can be adapted with sleeves)
thingiverse
Pegboard Holder for Stanley small screwdriver set (66-052) from Stanley Screwdriver 20 Piece set T186 (65-750B) My Pegboards have 25mm spacing and 5.5mm holes, so may not be compatible with USA pegboards.
thingiverse
This little rack is for those carburettor adjusting screw drivers ,the ones used on small engines, Pacman, double d, star etc, or use for any small drivers.. ...
thingiverse
Simply print the racks and arms and snap them together to hang on a 3/4" cleat wall. I used supports on the racks but not the arms. Lay everything flat. I also made a stubby rack for the stubby drivers. ...
thingiverse
Easy access to you adafruit #424 precision screwdriver set... Post Processing: I left the holes slightly smaller then needed so you can finish them to a perfect fit with a drill bit. The "clamp" attaches to the "main" with a short M3 screw. I...
pinshape
SummaryIt holds screwdrivers or anything else you want to put in it. Edit: Added a version with three different hole sizes after I had some trouble with large flat tip screw drivers. Holes are .3", .4" and .5". ... First version are all...
thingiverse
It holds screwdrivers or anything else you want to put in it. Edit: Added a version with three different hole sizes after I had some trouble with large flat tip screw drivers. Holes are .3", .4" and .5". ... First version are all .4" ...