scuf controller for xbox 3d models

I've seen stylized Xbox controller holders, but I hadn't yet found one of Ezio, so I remixed the Ezio bust (https://www.thingiverse.com/thing:3382847 ) with the Xbox controller holder (https://www.thingiverse.com/thing:3577991 ). Based on a...

This is a remix/mix of two Xbox controller phone holders that I liked a lot. I liked both designs, so I decided to customized them a bit to create my own phone holder. I recommend priting at 60 mm/s (if using an Ender 3) and to use as an infill...

Xbox One controller model, coming right up! I'm excited to get started on printing it out, and I've got a feeling that it's going to be a challenge. ...But don't worry, I've got a plan B - I'll remix the design to make it easier to print, and also add...

THIS EXACT VERSION HAS NOT BEEN TESTED YET PLEASE PROVIDE FEEDBACK - UPDATE 2017/11/21: Corrected File Upload and Enlarged Slightly - UPDATE 2017/11/21: Corrected Radius An Xbox One Controller Holder Design to Hold a Controller WITHOUT its Cable,...

This is a custom-made stand designed specifically for the original Xbox console. Feel free to print it out for your own personal use, but be aware that resale of this item is strictly prohibited. ...If you're interested in purchasing one directly from...

I created this Xbox paddle for a buddy who needed one that was roughly half as long as the original he found on Thingiverse. You can check out the original design by Jack Gooding here: https://www.thingiverse.com/thing:3485713. ... 4/16/20 - I updated...

On-top replacement TPU Knob for Analog Controller Sticks

(Just don't change the curve shape.)All edges are not sharp and chamfered with curves where possible and with a 45 degree chamfer on the backside edges. The curve fits the controller back perfectly and was tested over several iterations and...

Xbox 360 Wall Mount, with a 40-degree slant. Thanks for using my designs! Sponsor my filament/coffee? http://paypal.me/KR34T1V Please note that these designs are a "best effort" and are not guaranteed to work in your scenario. I am not an engineer...

Controller Operator

X-Box controller wall mount. Only one screw needed. ...No support for print needed.

On-top replacement TPU Knob for Analog Controller Sticks

This is a Remix that I did from 3DXia from his playstation design. Recommended Settings:Nozzle 0.60,2 layer high25 infill for all3 walls You can get away with a 0.4 Nozzle and 15% Infill, Also I had issues with my Kobra with the overhands but I flip...

A simple stand without the xbox logo. ...You can print the logo with an another colour and merge it with the stand with a little bit of glue.

It can be printed without supports, as long as your bed adhesion is reliable, so all the details stick down.My print settings:0.2/0.3mm layer height5% infill because I was just prototyping, but a little more can't hurtExtra parts:2x Rubber Bands, for...

Enjoy this BOX ONE controller holder. There are 2 versions. ...For one controller and for two. ...Didn't know what else to type into the summary window :)</p>

Console Player Controls Device

The compact design is compatible with the Xbox360, Xbox One and Steam Controller. ...To accommodate the Xbox One and Steam Controller, simply add a slight extension to the lip of the device.

Update: I've incorporated inserts for the xbox logo. Simply print them off and push-fit them into place. A quick sanding to remove a thin edge was necessary, but then I used the butt of a screwdriver to tap them securely in position. It's a shame I...

Check out this BOX ONE controller holder! ...It's a must-have accessory that'll keep your console gaming experience at its best. You've got two options: a single controller holder or a dual controller setup - perfect for playing with friends or family.

Hey there I have 2 models, the first is a 2 controller stand with 3 compartments (I used the middle for a rechargeable battery slot explaining the hole in the back for the cord) and the second for an under-the-table type hook held on with command...

A little larger to be more stable Added some fillet and rounded some corners too Replaced Xbox logo by the Starfield one This is a remix from ideawizard design (https://www.thingiverse.com/thing:2191646) Thanks !

Remixed https://www.thingiverse.com/thing:2191646 for my new Starfield controller. ... Printed in eSun Matte Gray, painted with Testors Gold model paint.

I liked the idea of the controller being under the table so I crafted this up in fusion. Insert controller and allow it to snap in, the bar inside should slide between the start and select buttons. To remove I push the lower portion downwards...

Added additional screw points for fixing the controller with support. ... The bottom screw is sized for M3 (Metric); refer https://www.engineersedge.com/hardware/_metric_socket_head_cap_screws_14054.htm for more information on the M3 sizing.

... the device. ...The storage compartment for spare batteries is conveniently located on the handle, ensuring quick access when needed. ...This design allows users to have both hands free while playing games or using the controllers in other applications.

I was thrilled with the original design, but I needed a spot for my trusty wired controller. Luckily, a fellow Fusion 360 master had shared an f3d file, so I imported it and made some modifications to suit my needs. To ensure a sturdy hold, I added...

I liked the original but needed a slot for my wired controller. I was happy to see a fellow Fusion 360 designer had posted an f3d file so I imported it and modified the design to meet my needs. Added some extra screw holes as well since I'm going...

I'm excited to share that I've upgraded my gaming setup with a brand new Xbox console from Mercedes-Benz. ...The sleek design and cutting-edge technology of this console are truly impressive, and I can already imagine the endless hours of fun I'll have...

I liked the idea of the controller being under the table so I crafted this up in fusion.&nbsp;Insert controller and allow it to snap in, the bar inside should slide between the start and select buttons. To remove I push the lower portion downwards...