scx10 2 battery relocation 3d models

Mount a TRX4 Trans on an SCX10-2 skid plate

Strategically relocates battery weight directly over the front axles, dramatically improving vehicle balance. Engineered to handle oversized 5000mah batteries while minimizing zero binding potential.\r\n\r\nRequiring two extended 3x20mm (AXA0439)...

Smt-10 quick and easy front relocation plates for the battery. Two version for a stubby and full size battery. ... Suggest 3 wall and 50% infill on them for the strength depending on how rough you are on the truck

The batteries that can be used with this mount are: - 2s 2200 single, laid down - 2s 2200 double, requiring a parallel harness for both batteries - 3s 2200 single, but caution: do not use with stock ESC I took twelve 2s 2200 batteries from RC...

This is a higher cover for the SCX10 2 receiverbox so you have more space for a bigger receiver, external bec, cables, etc.

Locates the battery tray parallel to the chassis and much lower for a lower center of gravity. The tray just clears the links when flexing on a stock suspension setup. ...Also allows more room for a scale interior,

The stock battery tray mount limits the uptravel of the rear axle, this can easily be seen by cycling the suspension upwards with the battery tray removed. Cut those stock mounts out and now the suspension will bottom out on the shocks and axle...

These two parts provide a straightforward way to mount your battery up front and electronics in the back of an Axial Wraith Spawn. The compatibility remains uncertain for the original Wraith model, but preliminary results suggest a seamless fit. No...

This is a dual servo mount and longitudinal battery tray for the Axial SCX10 and clones that use 70mm wide front crossmember.

I'm testing the new Axial SCX10 2 Cherokee with some initial stuff. To keep things tidy, I've opted for magnet mounts instead of drilling holes into the body. Both front and rear mounts are easily installed. ...The EU license plate is included along...

I required some external shock hoops for my scx10.2 project that didn't interfere with the frame and lacked body mounts. I printed them in PETG with 100% infill density. PLA or ABS should also be suitable alternatives. If you need some for a 10.1,...

This is a mount for the Reefs 99 Micro winch, it mounts behind the Steering Servo on a SCX10.2 chassis. I used an old antenna tube to run the winch line through, I uploaded a version with a mount for a tube and a version with no tube mount if it is...

3mm offset bumper mount to suit scx10 and scx10.2 frame can be inverted to suit desired height for fine fitment of bumpers may suit other chassis such as scx10.3 or element enduro

Post mount front bumper for Axial SCX10-2/SCX10-3 vehicles. (2) light buckets for 5mm leds, compatable with Axial light bucket lenses (AX80045). ...Uses stock pin hardware for mounting and (1) M2x6 screw for the led retainer.

This is my innovative design, take it for a spin - it's a winner when paired with an RC4WD Bruiser body attached to an SCX10 chassis, and it'll also perform flawlessly on the upgraded SCX10.2.

Durable battery housing device 90.

I design these low profile battery trays to allow me to run a more flatbed style bed as I was worried with the original my batteries wouldn't clear this will fit both the JL (313) and the JT(355) and there is a cutout to allow close proximity to a...

Displeased with the performance of the standard battery plate's pairing with a compact LiPo unit, I crafted an alternative solution from scratch.

Quick designs done to mount a body to a SCX10 Clone chassis.

I relocated the filament spool and runout sensor on my Anyqubic Kobra 2 Max to reduce the footprint. ...I was limited in space which necessitated the need to look for ways to reduce the area needed to house this beast!

direct fit to axial scx10.2, replaces servo and battery holder, require tapiing m3 thread since hole is tight fit, around 2.4mm. ...This may not fit all servo hole base in lenght, possible trimming in servo might be required

axial scx10- 10.2 30mm dropped towbar may suit element enduro , scx10.3 also replaces rear chassis crossmember 6x6mm square hitch receiver

Relocates tow strap point higher on scooter to keep thrust below diver for more efficient operation and less fatigue. Recommend use with neoprene buoyancy sheath on front of scooter made from the arm section of wet suit, which also doubles as...

1 use: Ender 6 Extruder Repositionig Relocation https://www.thingiverse.com/thing:4762567 Hand Filament Guide Remix Ender 6 https://www.thingiverse.com/thing:4762532 Ender 6 extruder hole cover https://www.thingiverse.com/thing:4790871 Ender 6 Cable...

These files modify the skirt of the voron 2.4 (300) to move the power switch from the rear of the unit to the front. The front L.H.S. skirt is modified to accept a 3 prong rocker switch that requires a 1 1/8 inch (28.6 mm) by 9/16 inch (14.3 mm)...

Quickly mocked up a new psu mount as I have dual z steppers The second z mount I used, works great https://www.thingiverse.com/thing:4771776 Take a look at what I have done to my Megazero 2.0! ...Ender 3 direct drive installed...

Simple rock slider I designed for the SCX10.2 Bolts right up to the stock location. ... Made to fit with the Axial Chevy C10 body

The servo relocation and battery trays can be used without the interior but the interior cannot be used without first installing the servo and battery tray. It is set up to use a 3S 2200mah LiPo but can take longer ones if you can find them. The...

This is a conversion of ECX Temper Gen 2 to use an SCX10 transmission, build details below; Printed Parts - Custom Skid takes this transmission https://www.ebay.com.au/itm/384135403059 - Custom Rear Battery Tray - Custom Front ESC/RX Tray - AR44 Link...

I wanted a stealthy front bumper for my SCX10.2 XJ, so I took matters into my own hands and created one from scratch. The first attempt was made with the front facing upwards in the printer bed, but unfortunately, it didn't turn out as well as I had...