scx10 cherokee body 3d models
100428 3d models found related to scx10 cherokee body.cults3d
tool free body removal and mounting set to suit hard body jeep cherokee bodys (xj 4door and 2 door), picks up on existing holes in the body and chassis , requires a few m3 bolts per side to complete
thingiverse
... Rock Slider erstellt. ...Abgestimmt auf den Jeep Cherokee von Axial (SCX10). Vorteil: man kann die Karosserie in den Rock Slider klemmen und die Seitenschweller in der Breite einstellen. ...Karo klappert nicht so, einstellbare Breite zu den Rädern.
thingiverse
Some test stuff for the new axial scx10 2 Cherokee. There are some mounts for magnets to avoid drilling holes in the body. Both for the front and rear mounts. ... There is an eu license plate, extra lights for special reflectors and rear lights.
thingiverse
Rear hinge mount for hard body Cherokee. ...Made it specific for my use but it might work for you too.
myminifactory
These wheel wells are intended for the Axial SCX10 II Kit Cherokee, and I don’t know if they fit other vehicles or bodies. The wheel wells also add that scale feature to your rig to make it yours. You will need to use two M3 x 20mm screws to mount...
thingiverse
Axial SCX10 2 Cherokee inner wheel wells to stop mud getting into the bodyshell. I have made them with PLA but a flexible material would be better, especially if you could change material and print the back support out of PLA or ABS and have flexible...
thingiverse
При печати необходимо увеличить ширину на 4мм. ...Тогда отверстия багажника точно попадут в штатные отверстия под багажник на кузове. You must increase the width of 4mm. Then the trunk hole exactly fall into the regular holes on the body the trunk.
thingiverse
I just bought a scx10.2 and wanted to adapt the body to fit the SCX10. I left it open to where you can set your own height for the body. it screws together with 2mm self tapping screws. tried to optimize it so you can get high resolution but not take...
thingiverse
this chasis/ body uses scx10.1 transsmision, skidplate, links, axles, 100mm shocks and 2.2 tires. i have fully built and tested body by letting it role down stairs fully assembled with nothing broken. know just working on paint and will have pictures...
cults3d
Turntable Video: https://youtu.be/1046Md3QmJI Here is a link to the Solid Files for fusion 360 https://a360.co/2I46FXb After printing the body mounts they seem a little thin to me, I will probably change them in a way that will not affect any other...
thingiverse
Turntable Video: https://youtu.be/1046Md3QmJI Here is a link to the Solid Files for fusion 360 https://a360.co/2I46FXb After printing the body mounts they seem a little thin to me, I will probably change them in a way that will not affect any other...
prusaprinters
I didn't make a panhard mount as that goes on the shock tower. Turntable Video: https://youtu.be/1046Md3QmJI Here is a link to the Solid Files for fusion 360 https://a360.co/2I46FXb After printing the body mounts they seem a little thin to me, I will...
thingiverse
Found this cool mount for the Hilux and adapted it for my Tundra body. The 1 mount is just like the original with higher body mount sides. The other mount has plates added for more electronics mounting surface. I also enlarged the pockets for the...
cults3d
Jeep Cherokee Printable Body Car, with different wall thicknesses. ... All models are prepared to be printed on different scales, the model has several versions with different wall thicknesses to facilitate printing.
thingiverse
Made a body post for my Axial Scx10 that was longer than the stock ones to fit a body for it.
thingiverse
Needed a body post tall enough for the XJ body for my first gen Axial SCX10 Honcho. Printed in ABS, the more infill the better. Its a perfect fit in the stock mounting holes in the rear. UPDATE: The posts that slide into the shock towers are...
thingiverse
Boudy mount for SCX10 and similar for rear bumper post - picture of it coming soon
thingiverse
this monut is for my jeep on an scx10 I fornt works great just waiting to print the back agian i made it to small the first time its 86mm tall from the scrow holes on the shock tower to the flatspot
thingiverse
Hide your body posts. ...I used velcro on the underneath of the body and on top of this. ... Velcro's body down.
thingiverse
this is my design try it out works with the rc4wd bruiser body mounted to a scx10 chassis will also work with scx10.2
cults3d
This body have dimensions for body AXIAL SCX10 wheelbase 313 mm width 222mm
pinshape
This is a Snorkel that will mount on the right side of your SCX-10.2 Cherokee body. ...Glue or fix with 2mm hardware.
thingiverse
Mounting system for the Axial SCX10.2 (maybe also 10.1?) for the Jeep Comanche hard body. ... See how it works here: https://youtu.be/AMc1iCY1EL4
thingiverse
front and rear body mount for scx10 and lc70 killerbody 1/10
cults3d
Jeep Grand Cherokee 1998 Printable Body Car, with different wall thicknesses. ... All models are prepared to be printed on different scales, the model has several versions with different wall thicknesses to facilitate printing.
cults3d
Jeep Cherokee 1990 Printable Body Car, with different wall thicknesses. ... All models are prepared to be printed on different scales, the model has several versions with different wall thicknesses to facilitate printing.
cults3d
Jeep Cherokee Limited 2019 Printable Body Car, with different wall thicknesses. ... All models are prepared to be printed on different scales, the model has several versions with different wall thicknesses to facilitate printing.
cults3d
Jeep Cherokee XJ 2000 Printable Body Car, with different wall thicknesses. ... All models are prepared to be printed on different scales, the model has several versions with different wall thicknesses to facilitate printing.
cults3d
Jeep Grand Cherokee 1977 Body For Print Scale Model •1:8•1:10•1:12•1:14•1:18•1:24•1:25•1:35•1:43• Also there are files with a wheelbase of 260 mm and 313