scx10 motor and esc 3d models

... click "Tip". If anyone has any requests, I'm open to trying to put some designs together. I have an SCX10, RC10B3, SCT410.3, Tamiya Hilux, Losi 5ive-T, Savage, RC10T (alum. pan) to be able to make parts for, or as dimension references. ...Thanks!

This is for brushless motors and their esc's. ...This was designed to make a fan.

This is a box I designed to relocate the ESC and receiver to the rear of the truck. It's spec'd for an original SCX10 so fitment may be different on the II, but I don't think so. I just don't have one to test. ...Sorry for the print quality, I'm still...

I designed this a long time ago and was designed for the original SCX10. I am sure this is obsolete for the latest version but those of you who still have the old frame might get some use out of this. ... This is design that was intended to be 3D...

Simple ESC tray that replaces the RX box location.

... rails. I used an existing hole in the frame and screw to secure it. Infill is up to you. Update: Went to fit my esc today and it was a bit tight. ...Added a second enclosure box that I trimmed back the screw mounts to allow for more clearance.

The motor mount is pretty solid as long as you print it pretty thick, 5+ walls, I've had good luck with pla and petg, but I expect abs would be best. The transmission flip mounts are not as strong, they work but they do break on me occasionally,...

Flip your 10 ii kit transmission and motor forwards for the best cg! The motor flip mount fits a good range of pinions, 10-14 at least, maybe a bit lower and higher. The motor mount is pretty solid as long as you print it pretty thick, 5+ walls, I've...

this is a part for the Axial SCX10 to take the RX and the ESC on a plate

Reicever/ESC/Button tray to fit SCX10 , ESC is hobbuwing 1080,reciever is a FlySky FS-GR3E in a balloon ..used double sided sponge tape to keep esc and button in place

Reicever/ESC/Button tray to fit SCX10 , ESC is hobbuwing 1080,reciever is a FlySky FS-GR3E in a balloon ..used double sided sponge tape to keep esc and button in place

This is an ESC for an Axial SCX10. ...It worked well with the ESC I have, not sure if it would fit other ESCs

I want to cool down de ESC unit whit the power of the main motor. The original micro electric fan on the controller it is not appropriate for this application. Its always broken by the hard shock from a crazy ride like i like to do.... lol. ...First...

This receiver / ESC mount is designed to be an easy mount platform for the electronics used on SCX10 style vehicles. The hole pattern is designed to give many cable tie / zip-tie options. For receiver waterproofing I use a balloon and some short...

Dual motor plate SCX10

The SCX10 Front Motor Mount will allow you to easily mount your motor and Axial stock transmission, on the nose of the SCX10 frame, and make tons of room in the center for a Transfer Case and Interior for your custom build.

SCX10 center side mount ESC tray. Dimensions are designed for stock esc but may fit others. Recommend using the longer 3x12mm (AXA436) self tapping screws to mount to chassis. ... I also have relocation mounts for battery and RX as well.

Rail sliders for my Axial SCX10 Deadbolt. ...Two piece design fits into original mounts and has a flat section to mount ESC and other electronic components low down to lower CG.

ESC mount for the SCX10 III to mount the larger MAMBA X ESC above the micro servo. Requires 2 x M3 x 6mm Screws and uses stock holes for mounting. Print in the orientation downloaded. ... 5 walls 4 Top & Bottom Layers Print using PETG

Fits max. ...20mm wide and 8mm high ESC and 28mm wide motor.

The Austar Injora SCX10 clone comes with a nice little receiver box but an empty space for the ESC. So I made a crate box to fit in the given slot on the austar right side plate. Use 2- M3x8 screws to fasten. The lid is a snap fit. There is only 1...

A direct bolt-on solution for mounting your ESC safely to your SCX10 utilizing RC4WD's AX-2 transmission. Designed to fit the "Honcho" body style, it has a pretty clean over-all appearance using 4 x 3mm fasteners for the lid itself. This works and...

And what if I needed to change the motors. Also I made a place for the ESCs to go. The stock ESCs most likely won't fit. But that is okay with me because I think the stock ones are junk. I also have a cover that will grab some cooling air. ...Hope you...

T-Motor ESC 15A

Models of the GOOLRC 3650 Motor and 60A ESCHeatsink to fit the 3650 motor is here: 3650 Motor Heatsink

Motor flip mount for the original scx10 transmission, A little bit thicker in design then my 10.2 style flip mount but otherwise a similar design. Should also fit 10-14 pinion, maybe a bit more and a bit less. I also mirrored my trans when I flipped...

Motor flip mount for the original scx10 transmission, A little bit thicker in design then my 10.2 style flip mount but otherwise a similar design. Should also fit 10-14 pinion, maybe a bit more and a bit less. I also mirrored my trans when I flipped...

Motor mount for 2204 class multirotor motor and ESC for scaled down (70%) FT Versa Wing with blunt nose conversion. Includes counter part for securing the mount to the foam. ... Instructions Use a Machine Screw Tap Drill M3 to cut threads into the motor...

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=167866 Instructions Using the following options: line_3 = line_2 = Motor No.1 line_1 = text_size = 7 plate_depth = 3 plate_width = 70 intend = 4 plate_height = 30 build_plate_selector = 1

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=167866 Instructions Using the following options: text_size = 7 plate_depth = 3 build_plate_selector = 1 plate_width = 70 line_3 = line_2 = Motor No.4 line_1 = plate_height = 30 intend = 4