sealcon cord grip 3d models
46693 3d models found related to sealcon cord grip.grabcad
SolidWorks 2014Cord range-.16" to .31" dia.Thread - 3/8" NPTMat'l: - 316 SSSubmersible- 10 barIP68/IP69Supplier - Sealcon USA
thingiverse
Customized version of https://www.thingiverse.com/thing:3212146 I customized this part from its original application of a cord toggle for small diameter bungy cord to suit our application which is a figure 8 style electrical cord grip to set the...
grabcad
Black plastic flexible cord grip for 1/4" OD wires, vacuum lines and air lines. Used for passing through bulk heads with lock nuts on both ends. ... Sealcon p/n CF09NR-BK Item # 24616 from Waytek Wire
thingiverse
A thing that hooks onto a shelf bracket, and the back of an extension cord to hold it up Note: while PLA may work, I recommend using a stronger material like ABS Recommended settings: use the build plate adhesion type, brim, to hold the print to the...
thingiverse
The grip I modelled was inspired by the original Nuprol pull cord grips to fit in the same housing and to be compatible with their flash mags. To fit the grip, simply pass the flash cord through the narrow hole on the top of the grip, tie a small...
thingiverse
this is an enclosure with two 11mm holes and two 5mm holes and a cord grip. ...i have used this design to house two missile launch switches and two LEDS.
grabcad
Mencom Corporation PCG-1/2X-B Modeled from manufacturer drawings and physical part
grabcad
69915K51 http://www.mcmaster.com/#standard-cord-grips/=mzwz4f
thingiverse
A quick simple cord grip sized to 12AWG wire. It grip with some 3x10mm screws to close it. Sized for M5 mounting bolts. Print with support on build sheet. ... #Thanks!
thingiverse
What separates this from other pulls I found on Thingiverse is that this can function as a coupler to extend the reach of your cord. The two halves simply screw together in a very secure manner. When assembled the seam is nearly impossible to see. I...
thingiverse
This is a cable gland for your small electronics projects, or whatever! There are three main parts: * the body * the cinch nut * and the cinch fingers (qty 10) I recommend printing the body with support due to the indexing collar on bottom...
thingiverse
Customized version of https://www.thingiverse.com/thing:3212146 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3212146
grabcad
Cord grip bar, 16mm ovalised fixing centres for M3 sized fixing screws. ...Made in Polycarbonate and suitable for strain relief of 0.75mm² 5-core cable.
grabcad
This is the Hubbell cord grip p/n SEC50GALN which is also Grainger item 415C69. The wire range is .17" to .45" and the threaded end is 1/2" NPT with a nut. ... The material is Nylon.
thingiverse
This is meant to help hold extra wire when building control cabinets. for some cable/wires (smaller diameter) you'll probably want to print the plug to hold everything in place. ...the plug can be zip tied in for extra security if needed.
thingiverse
Customized version of https://www.thingiverse.com/thing:3212146 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3212146
thingiverse
Customized version of https://www.thingiverse.com/thing:3212146 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3212146