secondary mirror holder 3d models
357133 3d models found related to secondary mirror holder.thingiverse
This is a secondary mirror holder upgrade for the Celestron FirstScope Newtonian telescope (76 mm aperture). This telescope is known for sometimes having the secondary mirror very unaligned. Furthermore, the original holder collimation has a very low...
thingiverse
Secondary mirror holder for DIY telescope. Editable FreeCad model included. For my telescope control software visit https://github.com/ZliRobot/RedShift Additionally required: 6 M3 screws 6 M3 nuts 1 M5 screw 1 M5 washer 3 M5 nuts Assembly process:...
grabcad
I needed a secondary mirror for my Newton, that could be possible to fine adjust in all axes
thingiverse
I designed this secondary mirror holder for my dobson telescope building project using a 203 mm diameter primary mirror and a secondary mirror with 70 mm of minor axis. This simple diagonal mirror holder has the basic 3 screws at 120 degrees to...
cults3d
I designed this secondary mirror holder for my dobson telescope building project using a 203 mm diameter primary mirror and a secondary mirror with 70 mm of minor axis. This simple diagonal mirror holder has the basic 3 screws at 120 degrees to tune...
youmagine
I designed this secondary mirror holder for my dobson telescope building project using a 203 mm diameter primary mirror and a secondary mirror with 70 mm of minor axis. This simple diagonal mirror holder has the basic 3 screws at 120 degrees to tune...
myminifactory
A simple secondary mirror holder for a diagonal mirror with a minor axis of 4 cm or more.I designed this secondary mirror holder for my dobson telescope building project using a 203 mm diameter primary mirror and a secondary mirror with 70 mm of...
thingiverse
1x M5x30mm Bolt to mount the secondary mirror (https://www.aliexpress.com/item/1005002413652525.html - 5pcs-50pcs M1.6 M2 M2.5 M3 M4 M5 M6 304 A2-70 Stainless Steel Black grade 10.9 ISO7380 Hexagon Hex Socket Button Head Screw) 3. 3x M4x30mm...
thingiverse
Additional material needed: - M3x45mm Screws (4) - for attaching the spider to the scope - M3x50mm Screws (3) - for adjusting the secondary mirror - M3x10mm Screw (1) - for holding together the secondary mirror holder - M3 Nuts (8) - 3 Springs - to...
prusaprinters
A Hadley remix for the secondary holder - The secondary bolt and washer are added via a slot without any need to consider the mirror - so you can glue the mirror in place any time you like. There is also no chance of backing out the secondary...
sketchfab
Secondary mirror optics included in the Schiefspiegler Telescope Mirror Kit. Provides sharp images. ...Make a telescope, get a super telephoto.
thingiverse
This is because of someone's request, about a model, to hold a smaller telescope secondary in their holder. Rotated so it should work, without support. Recommended to print or paint in black, to avoid any unwanted reflections. Note that the...
thingiverse
This is a 3 compartment box to safely store a Celestron C11 edge HD telescope secondary mirror, when the mirror is removed for Hyperstar operations. The box has a lid, a compartment for the secondary mirror, and a 3rd compartment to put desiccant. ... ...
thingiverse
Secondary mirror mount for my 8" dobson. ...I printed it with a Z-offset of -35mm to get a height of 65mm.
thingiverse
31 mm secondary mirror The primary mirror design is out-dated; Working on a new configuration that makes it easier to line up mirrors. Used a concrete cardboard tube which I strengthened by doing a fiberglass layup over top of it. The concrete...
thingiverse
The original secondary mirror holder of the [3" Celestron first scope](https://www.astroshop.eu/telescopes/celestron-dobson-telescope-n-76-300-firstscope-dob/p,15025) consists of a single rod, making collimation cumbersome. The design uses six m3...
thingiverse
... truss tube Dobsonian telescope. ...They come in two heights, depending on your desired design. Simple insert a connector bolt (M6 threaded, with 9mm diameter body), and you have a ready-to-use part onto which the secondary mirror can be attached.
thingiverse
card holder for the new secondary objectives, fits snug, lid is a tight fit, once u get it on and off a few times it is better. ...fits all new secondary objective cards from white dwarf, also will fit them if they are in sleves
thingiverse
Due to the height of my shower wall, it ends up holding the secondary head at a lower position than it is at when mounted to the primary head, which I prefer. ... I made the neck as long as possible, so be prepared to rotate it in order to fit it on...
prusaprinters
If you have or know someone who has a meade lxd55/75 SN10" and needs to center the secondary, I provide you with the 3D files of these parts that allow you to set the concentricity and rotation angle of the secondary mirror with great precision and...
thingiverse
This is an attempt to make a secondary mirror mount for a trackball telescope, specifically Jerry Oltion's design. The original Oltion design used a vitamin bottle cut at a 45-degree angle. It prints in two parts, which should be snapped together to...
thingiverse
This is an updated design for my other Secondary Shower Head Holder. After using it for a while, I found that it would be easier to replace the shower head in the mount if I removed some of the material from the lower portion of the clamp. I also...
thingiverse
... print part, and crash on primary mirror. It damage my primary mirror . So I draw a 35mm secondary mirror cover in order to prevent the mirror fall apart again (updated 2023/07/07) Add 25mm secondary mirror cover for D114F900 newtonian telescope
thingiverse
A Newtonian/reflector telescope requires a "Spider" to hold the secondary mirror in the center of the Telescope. This part is the fixture that holds that mirror and allows you to make micro adjustments to the angle and distance to ease collimation or...
thingiverse
32mm spider for secondary mirror, Newtonian telescope The system uses 4 M3 bolts with nut for the collimation system 8 M2 bolts to attach the legs of the spider, to the center piece 4 M5 wing bolts for fastening the spider legs to the tube body 4 M3...