sega controller 3d models

Sega controller directional control button new update

I designed this Controller Holder, cause I think it fits better than the other i Have found. Especially the rounded cable holder. The cable will have no contact to sharp edges. And its easier to print too. Best way to print is laying on the back,...

This is a stand modeled for the original Sega Dreamcast controller. Plug port in the rear. ...Separate print file for logo.

Sega Controller Stand, I used as a reference the design created by M4RCCR4FT for the NES and SNES controllers (https://www.thingiverse.com/thing:3403304). The logo is split in two pieces, the planet is part of the stand while the rings are in a...

This is a display stand for the Sega Saturn controller. I sell these on etsy, so if you want to purchase one, you can find my shop at telltaleatheist.com/3dstore I usually print in black and use white wood filler to fill in the logo. That...

This is a display stand for the Sega Dreamcast controller. Also works with USB. It takes two arms per base, so you'll want to print a total of three models to have the complete stand. I sell these on etsy, so if you want to purchase one, you can...

The Sega Genesis, known as the Mega Drive[b] in regions outside of North America, is a 16-bit home video game console which was developed and sold by Sega Enterprises, Ltd. The Genesis was Sega's third console and the successor to the Master System.

I am working on a stand for the regular controller holder. ...If you make it i would love to see it!!

Sega Saturn Controller Stand - specifically for the RetroBit Bluethooth controller. I cannot attest to its fit on any other Saturn controller unfortunately. ... Original Reddit Post for a picture:...

Same design as my original Dreamcast controller stand but with a VMU area in the front, because ya know...complete is complete.

The next in a mini-series for me, I have a friend with a large game/retro games collection, he wanted something to stand out on his drawers, I have put together a few sketches of controllers that will be the knobs.Then along comes this contest from...

Sega AstroCity Control Panel Attention, c'est un WIP !!!!

Hi, I took over the PS3 / PS4 controller support and after removing the logo, I replaced it with the one of the sega saturn.

I redesigned this stand to Screw it underneath my Shelf. ...And I added the Sega Logo at the Front. ...If you want to use this as a Stand just lower the Holder by 6mm in your Slicer Software.

This is a repair part for all the other fat fingered retro gamers who have snapped the inner D-Pad toggle on their Retro-Bit Sega Saturn controllers.

Designed this to make installing LED's in the SEGA DreamCast's controller ports easier and also to eliminate the need for any HOT-GLUE! Also lines the LED's up to shine straight into each port perfectly! I've been asked about this multiple times by...

End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515

Could not find a stand for te wireless Retro-bit controllers for the sega consoles - so I made my own. I printed mine with 0.3mm height and 5% infill without issue. ... Have fun, game on!

master system controller holder

The Sega Master System[b] is a third-generation home video game console that was manufactured by Sega. It was originally released in 1985 as the Sega Mark III in Japan. After being redesigned prior to its North American launch, the console was...

Sega Saturn wall mount with logo. ... I have read in the comments that the 3d controller for Sega Saturn would fit the design from https://www.thingiverse.com/thing:3769372 so I redraw it and placed the Sega Saturn logo on it.

This is a D pad for a Sega Megadrive 6 button controller, my original one sheared off so I designed this replacement. For best results I used a flexible filament mainly for comfort, I used TPE for this but TPU should work just as well. I...

Two-piece controller holder. ... It attaches the screw-holes on the back of the controller. ... Thanks to [Makros_the_Black](https://www.thingiverse.com/Makros_the_Black) for testing this design.

... holder. ... It attaches to two of the screw-holes on the back of the controller. As I'm not sure whether there are different versions of the controller you should check for those holes before printing (or print the dock stl first & check if it fits).

Yeah, this is another SEGA Mega Drive/Genesis controller keychain model. ...I saw some similar models around here, but I was not impressed by their accuracy (no hard feelings colleagues designers :) so I've decided to create one of my one.

Broke one of the arms that press the rubber in a replacement controller. Measured up a rough replacement part and it works well. Thought others could use it. Print Settings Printer Brand: Up! ... ...

Enclosure for compact version of PCB for Sega MD controller adapter found here: https://github.com/eyvind/sega-adapter It consists of 2 pieces - box and lid. Strap can be used to attach cable. ...

I could not find a good controller mount for the sega genesis 3 button controller so i tried making one. its not perfect but it fits the controller nice. ...i have a prusa mini and i used supports

I could not find a good controller mount for the sega genesis 3 button controller so i tried making one. its not perfect but it fits the controller nice. ...i have a prusa mini and i used supports

An enclosure for this open source adapter PCB: https://oshpark.com/shared_projects/qSqtcGAw I use a standard DB15 male connector for the Neo Geo half and the female plug end from a Sega Genesis / DB9 extension cord, salvaging the strain relief from...