select parts 3d models
571789 3d models found related to select parts.thingiverse
This is a selection of kossel's part to use fishing line, 2020 aluminum profil and 8mm smooth rod. This is a work in progress !! ... Instructions Print: 1 X Kossel_Rav_Alt_bottom_support.stl 3 X...
thingiverse
This is a part for the Select comfort beds. This should help out with the breakdown of the side foam panels that break down and have to be replaced about every 6 months. I have not tried this as of yet but did try a proto-type which worked very...
thingiverse
This is a part cooling blower duct I made for my Maker select plus. It uses the existing 2 bolts that hold the rear electronics cover on. This part will replace the cover on the back. This part uses the upgraded blower type fan. **Because this...
thingiverse
Parts 3mm screws of appropriate length & 5015 Good Blower (12V for MonoPrice Maker Select V2) Use ABS although PETG ought to be fine. I designed a raft and support into the model and found it came right off without difficulty when using ABS. Use...
thingiverse
I took this design i found, refined it, and also added chambers for 3mm nuts to make sure this cooler doesnt fall off your extruder.
thingiverse
I got a Monoprice i3 Mini from a friend which has a lot of missing parts. some of them could be 3D printed hence created these. - Leveling screw. The Level screw has an insert for M3 nut, hence pause print at a height where the layer over the nut...
thingiverse
These are the parts required to convert the Autococker Trilogy Select Fire frame to a pneumatic trigger without any modifications to the frame. You will need: These parts MSV-2 valve Various air fittings 2x 6-32 x 3/4" screws 2x 6-32 nylock nuts 6x...
thingiverse
Simply removed the LED holes from USWaterRockets original design to make for a simpler part cooling fan.
cults3d
Simply removed the LED holes from USWaterRockets original design to make for a simpler part cooling fan.
thingiverse
This is simply a mesh of the zero offset bracket by uswaterrockets and the articulated part cooling bracket by maxstier.
thingiverse
This Episode based on https://www.thingiverse.com/thing:2754973 Today we add a 30mm Spacer to the X-Axis without any new Parts must be bought. This can be done by removing the X-Axis-Linear-Bearing, move the inner Rod-Holder to the outside. The Rods...
thingiverse
I've been using the original 40mm fan duct that integrates with the popular E3D zero offset mount. This is the E3D mount: https://www.thingiverse.com/thing:1835673 and this is the original fan duct for this remix:...
thingiverse
I needed a 40mm hot-end fan shroud without part cooling to test out different settings for printing PETG and didn't find one in the first 5 pages of my Thingiverse search. ...This is a remix of https://www.thingiverse.com/thing:2896738 where I cut off...
thingiverse
Included in my set: -Rachet Spacers (to tighten the Combiner joints) -Fully Posable Hands with Weapon Adapter -Ankle wedges to eliminate wobbles -Back mount for the Massive sword -Shoulder joint spacers to fix proportions and get past chest spikes...
thingiverse
... 200, 40mm/sec. The part on the right is this version of the fan. The part on the left is the last version. Print Settings Printer: Monoprice Select Mini Rafts: No Supports: Yes Resolution: .2188 Infill: 30% Notes: Print fan side down with supports.
cults3d
Base mode designed to attach with the Selects StarConvoy or POTP Optimus Prime (or POTP Nemesis Prime) . The pieces give a base mode platforms similar to what the G1 original toy. Platform with ramps and Dual cannons. Micromaster Docking Base is...
thingiverse
270° cooling fan duct for Monoprice Makerselect v2. No extra nuts and bolts required. ... Fan I used: https://amzn.to/2IAYEa7 (affiliate link)
thingiverse
### Introduction: When printing my Z braces for the Plus, I found that it was a bunch of "take this part from here, this part from there, etc." and I ended up printing some parts I didn't need. Therefore, I decided to remix the parts I used into a...
thingiverse
This Series will start a development of my Wanhao Duplicator i3 v2.1. This Episode will push the X-Axis holding Frame both 30mm wider and the Bridge 30mm higher to allow further developments. Azza´s Z-Brace will be supported. How to: 1. The...
thingiverse
... Required parts: 8x M3 Lock Nuts (https://www.amazon.com/Team-Associated-25215-M3-Locknut/dp/B000BO6KUE/ref=sr_1_2?ie=UTF8&qid=1482122022&sr=8-2&keywords=m3+lock+nut) If you have any questions just drop a comment and I will respond as soon as I can.
thingiverse
* I've added support to the top blower screw mount so that it no longer needs support to print, it is touching the build plate * The screw holes have been adjusted to fit M2 bolts, since that's what's standard on the Mini Select V2 and I had a bunch...
thingiverse
I noticed that there wasn't any MPSMv2 40MM fan adapters AND 5015 part blower adapters already on the MPSM Wiki so I went ahead and designed my own, and would love to share with the community. Some benefits of this design: - improved print...
thingiverse
Customized version of http://www.thingiverse.com/thing:735038 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=735038
thingiverse
80mm fan duct for the printer to end all printers. ...Hoping it really kills it for printing PLA FAST AF.
thingiverse
ORIGINAL FILES: http://www.thingiverse.com/thing:921948 TO FIT ON MONOPRICE MAKER SELECT PLUS SELECT THE "Maker_Select_duplicator_i3_PLUS_Z-Brace_mod.stl" THIS ENTIRE FILE WILL PRINT ON THE BED (IT WILL FIT WITH NO CRAMPED PARTS) IN THE COMMENTS I...
prusaprinters
Ali express: https://www.aliexpress.com/item/1005001333983887.html?spm=a2g0o.order_list.0.0.71cc1802l0WvKo There are two parts. The knob press fits into the mount I made. The control board screws into the board mount using M3x6 screws. ...Use VHB...
thingiverse
Customized version of https://www.thingiverse.com/thing:3199259 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3199259