select the appropriate reagents for the following transformation 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=47032 Instructions Using the following options: eyes diameter = 3.5 legs number = 2 ring thickness = 3 layer height = 0.25 legs spacings = 2 shape = toes angle = 80 body thickness = 4 toes...

http://www.thingiverse.com/apps/customizer/run?thing_id=47032 Instructions Using the following options: ring_outer_diameter = 9 shape = 040,020,030,008,005,013,000,015,005,030,050,025-,067,010,003-,010- toes_angle = 80 legs_diameter = 2...

Instructions: Customizing the Following Options: Shape - 040,020,030,008,005,013,000,015,005,030,050,025-,067,010,003-,010- Layer Height - .25 Toes Angle - 80 Toes Length - 4 Ring Thickness - 3 Ring Outer Diameter - 6 Legs Spacing - 2 Eye Diameter -...

Instructions Using the Following Settings: Angle of Toes: 80 degrees Spacing Between Legs: 2 Rounding Level: 2 Eye Diameter: 2.5 mm Toes Length: 4 mm Layer Height: 0.25 mm Parrot Body Shape: Based on Design #8 (Standard) Orientation of Rings:...

To print this customized model, follow these instructions with the specified options: legs spacing of 2, toes angle of 80 degrees, ring outer diameter of 6, layer height of 0.25, rounding of 2, ring orientation of 2, toes length of 4, shape of 049,...

The customized version of this design is available at http://www.thingiverse.com/thing:47032, which was created using the Customizer app with the specified options. With a toes length of 7, ring thickness of 3, legs spacings of 2, eye diameter of 4,...

The following options were used in the customization process: center = 1, status_led_hole = 1, header_fontface = orbitron, footer_rotation = 0, footer = 0, footer_fontface = orbitron, footer_type = 2.85, footer_vertical_align = 0, header_size = 9,...

Instructions Using the following settings: layer_height is set to 0.25 legs_number has been chosen as 2 toes_angle is fixed at 80 eye_diameter measures 2.5 body_thickness is 4 units high ring_orientation is 1, positioned at a single setting...

The ring thickness is set to 3, toes angle at 80 degrees, eye diameter of 2.5, body thickness of 4, ring orientation as 2, legs number at 2, beak separation ratio at 67%, toes length of 4, leg spacings at 2, legs diameter of 2, rounding level 2, and...

http://www.thingiverse.com/apps/customizer/run?thing_id=47032 Using the following options: legs spacing set at 2 Beak separation ratio finely tuned to 67% Toes positioned at an angle of 80 degrees precisely Eye diameter calibrated at a precise 2.5 mm...

Shape options are set as follows: twenty-one, twenty-one, forty-five, three, six, forty, one, fifteen, four, thirty, sixty-eight, sixty-seven, eight, zero, ten. Legs quantity chosen is two. Rounding has been applied with a value of two. Eye diameter...

... of foam plastic, then it will definitely not sink. The semicircular end was made to avoid supports in the hollow part. On the pictures you can see the casing and the camera for clarity's sake. ...In the files only the pen and its plug are included.

2 positioning grids for player boards for the boardgame DAIMYO (for commercial game version only). ... Let me know if you have any questions or comments.

There's room for all the game components, once you throw away the original cardboard insert, including a pen/pencil and a rocket to replace the cardboard first player (commander) marker. The game is often played over many sittings. So, also pictured...

I've included a one-piece version for larger print beds, as well as a three-piece version for smaller printers like the Ender 3. The latter version includes dowel holes. Required hardware: M5 bolt and wingnut for securing the handy into the clamp. ...I...

- A perfect set of armor that consists of several unique parts: - shoulder pads, - neck armor, with cloak mounts, - The chest armor consisting of several plates, also a plate in the form of a bat, - armor for the torso and abs, - Batman mask. -All...

The heatsink is therefore mostly in the wake produced by the motor and bearing housing of the fan, where very little air is actually flowing.This model, the DragonTamer, is a small air guide which forces the air from the fan to pass through the...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

The coat rack for 20mm pipe. Print the pieces flat and glue them together to maximize strength based on the layer directions. ...You don't glue the rack on the pipe, though :-) so you can adjust the position as needed. Category: Household Supplies

This is just the glow for the Forbidden Watchtower by kijai. I crafted a cylindrical light to fit it in the tower, giving it an appearance of an illuminated landmark. The Tower can be found here: https://www.thingiverse.com/thing:2574499. ...I printed...

To learn everything you need to know about this fantastic antenna mount, check out these valuable resources: Visit the official Facebook page of Clover Frames at https://www.facebook.com/CloverFrames/ for all the latest information on "The Peach"...

Antenna Mount for "The Peach" by Clover Frames All informations about the frame can be found here: https://www.facebook.com/CloverFrames/

This Thing is a spare foot for the dishwasher. ... Use an M8x65mm screw with a hexagonal head to stabilize the foot and it will never break off again.

... the file size couldn't be optimized for Sketchfab, resulting in choppy playback. This is the first time using Marvelous Designer for character development, and the animation runs at half speed, but the audio fails to synchronize with this setting.

The Hunt for Medusa STL Pre-supported files, test printed, and ready to print Your personal google drive links will be given after purchase in the ZIP file

The user specifies a print setting of 0.2 millimeters for the first layer, 30% infill density, and a nozzle diameter of 0.4 millimeters.

Video This is Foldable spool for the plactic without spool.  The spool prints without any supports and at once.  I think it's an interesting decision. 

:) https://youtu.be/St7e_70tRnY I have all the dimensions for the wood in the photo. Because some parts are small maybe it will need to change the scale from printer to printer so everything can fit nicely. You can find some of my builds and support...

You'll need at least two more parts to make the follow focus work. ... 1: https://cdn.thingiverse.com/assets/b4/df/bb/cf/73/FF_SmallGear.stl 2: https://cdn.thingiverse.com/assets/41/cd/a6/1c/98/FF_Body.stl Remix of main_knob.stl:...

http://www.thingiverse.com/apps/customizer/run?thing_id=47032 Using the Following Options: beak_separation_ratio is set to 67, precisely the body thickness stands at a remarkable 4 millimeters eye diameter has been calculated to be exactly 2.5 toes...