sensor enclosure 3d models
60269 3d models found related to sensor enclosure.myminifactory
Hall effect sensor enclosure with screw holes and hole for snap in place 3 Female 2.54 Jumper Wires for retro indoor exercise bike.
thingiverse
I am looking for a filament runout sensor enclosure that fits my Omron micro switch. However, none of them I like and fit. ... So I just go ahead a create my own.
prusaprinters
I am looking for a filament runout sensor enclosure that fits my Omron micro switch. However, none of them I like and fit. ...So I just go ahead a create my own.</p> <h3>Print instructions</h3><p>Category: 3D Printer Parts</p>
thingiverse
This is a simple, 32mm pipe attachable, multi-sensor enclosure, for outside projects. Remember, if you are printing with PLA, you MUST spray some paint, resin or something resistent to the environment. PLA it's not water proof, it tends to absorb...
prusaprinters
It could be used with an adhesive backing for other materials. The tall lid includes space for a small desiccant packet for mitigating moisture intrusion, and makes the sensor enclosure roughly .75"/19mm tall above the attachment tabs. This is...
thingiverse
The tall lid includes space for a small desiccant packet for mitigating moisture intrusion, and makes the sensor enclosure roughly .75"/19mm tall above the attachment tabs. This is helpful for one or more wraps of .75"/19mm wide electrical tape to...
thingiverse
This is a dusk sensor enclosure. The main unit has holes for screws and the top slides on. This is installed outside and is used to steer the orientation lighting in a house. The circuit is a simple 741 opamp with 2 LDR's and a resistor divider...
thingiverse
Flite sensor enclosure for a time of flight sensor ONLY
thingiverse
Enclosure for MH-Z19 CO2 Sensor The enclosure for MH-Z19 CO2 Sensor, which clips in also OLED1306 LCD and ESP32 development board. I use the following firmware.. Connect using a usb > serial connecting to TX0 and RX0 I used the included...
thingiverse
Simple rain sensor (YL-83) enclosure for ArduMower. ...Fits to original mower frame.
thingiverse
Simple snap-fit enclosure for my ESP32 Door Sensor. ...Find the full description here: https://blog.squix.org/2020/04/esp32-door-sensor-part-1.html
thingiverse
I created this DHT enclosure to give the DHT sensor extra protection. ...This will fit a DHT Sensor that has a circuit board mounted to it.
thingiverse
This is the enclosure for the multi-sensor featured in this [YouTube Video](https://youtu.be/tVTha44i8SI)
thingiverse
Here is an Enclosure that I have designed for my Arduino Door Sensor using My Sensors. ... If you want to follow the tutorial to build the sensor yourself, check it out at the SmartHomeBlog...
thingiverse
... for an Arduino Nano with an I/O breakout board attached. ...This houses a DHT11/22 temperature/humidity sensor, a AM312 PIR sensor, and a KY-018 light sensor. ... One of the poles holding the DHT sensor is threaded so you can use the nut to hold it on.
thingiverse
Enclosure for Air Quality monitoring sensors. Device based on ESP8266, but you also can use ESP32. Sensors are: - SDS011 - PM 2.5 and 10 um laser sensor (biggest part) - Senseair S8 - CO2 sensor (note you can do an automation to control...
thingiverse
A project I was working on required a laser tripwire solution so I picked this up on amazon. ... https://www.waveshare.com/laser-sensor.htm It needed an enclosure so I mocked up a quick one. ...
thingiverse
Enclosure for Wemos D1 mini based air sensor. There are two chambers separated by the empty space in order to minimize the heat dispersion from the main module to the SHT30 sensor. Measurement proved, the heat spreading via the air and the circuit...
prusaprinters
A neat enclosure for the Multi-sensor project by Ben from Bruh Automation. It has the light sensor at the top with the LED, the motion sensor is at the front and the Temperature/Humidity sensor is to the right. ...There are 2 versions of the top, one...
thingiverse
A neat enclosure for the Multi-sensor project by Ben from Bruh Automation. It has the light sensor at the top with the LED, the motion sensor is at the front and the Temperature/Humidity sensor is to the right. There are 2 versions of the top, one...
thingiverse
They are perfect for arduino projects: http://www.amazon.com/gp/product/B008AESDSY/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 The enclosure holds the unit and has tabs for #6 screws. ... Instructions I...
thingiverse
This is an enclosure I built for this sensor: https://home-assistant.io/blog/2015/10/11/measure-temperature-with-esp8266-and-report-to-mqtt/. It houses an ESP8266 board, a DHT22 sensor, and a battery https://www.adafruit.com/product/2011. The...
pinshape
This is a simple enclosure for a SDS011 Nova Dust Sensor. I didnt find a useful enclosure on the internet, so i quickly designed one. The dust-Sensor measures the dust and in combination with an WeMos it will send the results into the cloud or to...