serial port cover 3d models
165188 3d models found related to serial port cover.cults3d
Special port cover, CL serial port 6mm to 1.2mm then 8.1mm through remainder With and without handle Updated for scaling 8/19 5:40pm left coast time
thingiverse
Special port cover, CL serial port 6mm to 1.2mm then 8.1mm through remainder With and without handle Updated for scaling 8/19 5:40pm left coast time
thingiverse
Snap in covers for the Video and Serial ports on Commodore Computers. I have tested the round 64c style inside a Pixel Wizard and original 64c case. I also did test it in a C128 flat case, but its very tight. Might need some sanding or reduce...
thingiverse
... extended a little out. ... Note that this was the case for a first edition GameCube (the one that brought the digital ports). I believe that they have the same cover dimensions as the more widely available GameCube, but wanted to throw that out there.
thingiverse
Replacement for the Serial I Cover on the bottom of your GameCube.
thingiverse
Replacement for the Serial II Cover on the bottom of your GameCube.
thingiverse
Remix of front cover by [DanAndersen](https://www.thingiverse.com/danandersen/designs) https://www.thingiverse.com/thing:4801381 Front panel for Chieftec IX-01B computer case. ...I added holes for 2 usb and 1 serial port connector.
thingiverse
Here we have a Serial Port cover for the Nintendo GameCube designed to house the BlueRetro ESP32 project for connecting Bluetooth Controllers See here for the BlueRetro project: https://github.com/darthcloud/BlueRetro/ This is designed to hole the...
thingiverse
Serial port cover, designed to fit snugly inside RS232 port. ... Designed for GPD MicroPC
prusaprinters
Uses 4 M2*6 screws and M2 nuts (M2.5 should work as well).I printed this on a resin printer for accuracy.Note: the creator of PicoBoot recommends you don't install it in the Serial Port 1 bay, due to wire length and potential future upgrades that...
prusaprinters
Gamecube serial port picoboot mount. This is for mounting the Pico in the bottom of the gamecube. Printed on 0.2 layer height. Remember to remove the extra print from the clips. ...This is just to make them better when printing</p>
thingiverse
I need a lid with a hole to connect the serial port, so i decided to make a usefull remix of the original design. I've only uploaded the Lid, you have to print the original base from the original design. ... Remixed from:...
thingiverse
Serial number cover for scooter / motorbike lifan and others chinese copy :)
thingiverse
This is a alternative shell for mini pc MK802 II with hole for serial port
thingiverse
HP 100LX and 200LX handhelds use a custom serial port connector. This is a shell for 2x5 pin header with 2mm spacing. ...The fit is tight, no glue needed.
thingiverse
I use a lot of the very low cost Cp2102 serial ports for my robots seen on mark-toys.com and have finally made a protective cover that also adds support for the board. Here are two choices for a protective case that also makes the Cp2102 unit less...
thingiverse
Can be used in usb to uart PL2303HX Like this: https://www.ebay.com/itm/USB-To-RS232-TTL-PL2303HX-Serial-Cable-Converter-Adapter-Module-For-arduino-AU/172748865399?hash=item2838a27f77:g:8~UAAOSw-89ZUMBw
thingiverse
This 3D-printable part allows replacing the factory port cover on the top of the device with one providing extra space for a female .1 inch header to expose the internal serial port permanently on the outside. ... The "G R T" designator indicates...
thingiverse
... as a support for two antennas for internal WiFi (and Bluetooth) cards. ...The antenna bolts can be firmly screwed to the plate and the plate itself can be screwed to the case using the standard size of a VGA or Serial port (same size as the VGA). ...
grabcad
FT232RL 3.3V or 5.5V FTDI USB to TTL Serial Adapter Arduino STM32 Mini PortRed board
grabcad
A 4 port USB to RS232 (4X) converter from DIGI.com.
thingiverse
I needed a "dust cover" for a USB port that failed on a 5-port charger. I was always forgetting which port was bad... and then I'd wake up and some device hadn't charged all night. I put an X on the bottom/part facing out so that people think before...