sewing thread holder 3d models
408247 3d models found related to sewing thread holder.thingiverse
Sewing thread holder for many sizes spool of thread. ...Use double sided tape
thingiverse
Singer sewing machine thread holder. ... fits to: https://www.thingiverse.com/thing:359811
thingiverse
This is a simple holder system for sewing thread reels for overlock sewing machines. Each one holds four reels and they can be clipped together to form a platform for several colors. (I am not sure if the name of this thing is correct since this...
prusaprinters
I printed these to store my sewing thread in the wide Ikea Alex drawers. There are pieces with a flat edge for along the front of the drawer and ones with two flat edges for the corners. ...I have found I can store a matching bobbin on top or under some...
thingiverse
yarn holder Instructions Printed with Makerbot at 0,3mm; 10% infill; 230°C
thingiverse
... I had to increase the height of the spool holder bridge to prevent it from sagging. I also added two bottom supports and a bobbin holder. ... Due to the particular spools I use,I have to organize them as shown in the photo so they can fit together.
thingiverse
I made this for my wife to hold her thread spools. The posts are printed separate and on their side for strength. Just slide them up from the bottom and push them in place. Depending on your printer's tolerances, you may have to hammer them in...
prusaprinters
I made this for my wife to hold her thread spools. The posts are printed separate and on their side for strength. Just slide them up from the bottom and push them in place. Depending on your printer's tolerances, you may have to hammer them in...
thingiverse
I made this modular sewing thread holder. Prints flat, parts snap together. Snap together the Leg pieces first to make it easier. Rows can interlock and the spacing between spools is very compacted. A revision is made where the interlocking row...
thingiverse
Der Nähgarnhalter kann mit dem passenden Ständer hingestellt werden oder aufgehängt werden. ...
thingiverse
Sewing thread feel holder 25mm 2019.01.31 Holes changed to 26mm
thingiverse
The holder is attached to the spool with self-tapping screws. ...8 holders need to be printed for one spool.
cults3d
I put a piece of cardboard between the sewing machine and the roll holder with the intention of creating some friction and thus slow down the roll inertia of the roll. ** 1-01-2021 ** I've added three more new options. One with 6mm hole, one with...
thingiverse
Designed this to help my mother's sewing cabinet be more organized, the dimensions of the holders were decided to look at the build volume of my printer. I have also attached .sldprt files for increasing the number of rows. ... Do note that there is an...
prusaprinters
Designed this to help my mother's sewing cabinet be more organized, the dimensions of the holders were decided to look at the build volume of my printer. ...I have also attached .sldprt files for increasing the number of rows.Do note that there is an...
thingiverse
... held my paints and how it connected to my peg board perfectly. ...Needed one for my spools of thread, but they wouldn't fit in the paint holes, so I remixed it to have the same back side as the paint holder but with pegs on the front for thread spools!
thingiverse
Just a little tool to organize sewing thread spools. I made this as my very first thingiverse object for my girl. It measures 210 mm by 152 mm to fit into a box that was lying around. Space for 34 spools leaving enough space for your fingers to...
thingiverse
The bar is 8 mm diameter, i've used aluminium the lenght depends on your sewing machine and your spools :-D I don't think you need much more info....
thingiverse
Large size takes 6mm rod, small size take 3/16” (roughly 4.8mm) rod Also 2 version of the Bobbin Wheel, large diameter takes 6mm rod, the other takes 3/16” (roughly 4.8mm) rod 1 x Central rod 8mm x230mm (longest I had) 2 x horizontal rods 3/16 x...
thingiverse
My mum asked me to create a holder for her sewing threads... ...this object is the result.
youmagine
If your Thread holder in your IKEA sewing machine breaks, then here you have a replacement part. I used slic3r and printed with the following parameters with good results. ... layer_height = 0.2 perimeters = 2 top_solid_layers = 3 ...
cults3d
This is a horizontal holder for conical sewing thread spools. For its design I have used a Singer 518 machine as a reference. This is the machine I have. This model belongs to the 500 series which includes the models 518, 538, 514, 513 and 533. It...
thingiverse
This should hold the coil of thread on my Chinese leather sewing machine. It has been otherwise getting stuck and tangled. I will print this in the morning and try to get pictures uploaded. ... I believe the pin the spool sits on is 1/4".
prusaprinters
The spacing has been adjusted to allow the model to fit Gutermann spools and also the larger pieces resized to fit on the bed of an Ender 3.Print six of the spool holders and two of the stands (one normal and one mirror image) and then glue together...