sg13 sfx bracket 3d models
74562 3d models found related to sg13 sfx bracket.thingiverse
A 3D printable version of the bracket I used to mount my power supply to the front of my SG13 case. Requires an itx or a shorter GPU. I used spare PSU screws to mount it to the SSD spot and another hole in the front as shown in the photos. ... I...
thingiverse
... bracket for the Silverstone SG13 mini-itx case. ...Requires an itx GPU so the SFX PSU can be mounted at the front of the case instead of the top, I used another bracket for that, I used spare fan screws and leftover case screws to mount the bracket.
thingiverse
A simple bracket for SFX power supplies. It can be used in two orientations on a STEGO BOARD 400. Apply glue to the insides of the support holes and the small ridges nearby. Center the stems and place them inside firmly ensuring there is no gap while...
thingiverse
This is a replacement SFX PSU bracket for the Ncase M1. ...It uses a total of 5 countersunk screws to make it secure. Three of these screws are already used for the original SFX PSU bracket, but there are extras for use behind the case's front panel.
thingiverse
Broke the SFX PSU Bracket that came with the case so I made this one, looks much better anyways. ...Leaves just enough room for a 25mm thick fan on top.
thingiverse
AP201 SFX-L PSU Bracket Mounting the PSU this way allows a front 120mm intake fan, optimal airflow to the PSU, 360mm radiator with tubes on right side, and extends the GPU support to ~360mm. ... Filament used: HATCHBOX PETG Black...
thingiverse
Designed so I could mount a TFX PSU in my SFX (Checkmate A1500) Case. This can be used for a "Fan down, left side" orientation, or "Fan up, right side" orientation. ... Ironically, the TFX PSU I ended up using had cables that were __too__ __short__...
thingiverse
Requires additional parts listed below: Qty: 2 https://www.mcmaster.com/6391K738/ Qty: 1 https://www.mcmaster.com/91259A711/ Qty: 1 https://www.boltdepot.com/Product-Details.aspx?product=7242 Qty 1:...
thingiverse
The Supermicro 836 3U chassis redundant power supply to SFX conversion bracket as seen on https://www.wanhunglo.com/2020/fitting-a-proprietary-supermicro-x9srw-f-into-a-standard-3u-836-case-p23 . If you can, please use the RSDOC (RS DesignSpark)...
cults3d
The outer holes have fully modeled threads so the standard 6-32 screws that come with the PSU or PC case can fasten onto the adapter bracket with relative ease. ...Just print the part with a layer height of around 0.22mm or smaller so that the printed...
thingiverse
The outer holes have fully modeled threads so the standard 6-32 screws that come with the PSU or PC case can fasten onto the adapter bracket with relative ease. ...Just print the part with a layer height of around 0.22mm or smaller so that the printed...
thingiverse
A 92mm fan bracket for Silverstone SG13 mini-itx case. Requires an SFX power supply and AIO CPU cooler. ...Mounts on side matching case holes.
thingiverse
I wanted to keep my three drives when changing my case to the SG13 but with the modular cables on my PSU, I had some problems with the original drive holder which is mounted on top. Print with the flat top side as base. Print one holder mirrored.
thingiverse
this is an in-progress front panel for my sg13. The parts needed are listed bellow. ... https://www.amazon.com/gp/product/B07QMQV3FF/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 https://www.mcmaster.com/92446A108/
thingiverse
I have designed little compliant inserts that allow you to repurpose the 120mm AIO bracket in the DAN A4-SFX to mount a 3.5" HDD if you have a short GPU. The compliant legs slot into the slots on the AIO bracket and provide a hole to screw a 3.5" HDD...
thingiverse
Adapter for SFX-PicoPSU-Mini-PC with holes for: 1. 60mm Fan 2. Potentiometer 3. ...Powerplug
cults3d
Adapter for SFX-PicoPSU-Mini-PC with holes for: 60mm Fan Potentiometer Powerplug
thingiverse
I built a mini ITX system with the SilverStone SG13 case. I love the case but I do not care for the layout. I dislike water cooling and wanted to make the most efficient use of the space by redoing the layout. I relocated the PSU to the front of...
thingiverse
A 92mm fan bracket for Silverstone SG13 mini-itx case, but rounded.
thingiverse
For Silverstone SG13 replace default front fan cover. This V0.1 version not fit 100%, need to file the edges, or measure and edit the file in Fusion 360 or Invertor. ... Printed on Ender 3 V2
thingiverse
an extension for the Silverstone Sugo SG13 that makes room for an Nvidia 30 series GPU, made for a friend. the clips on the front panel will need to be clipped off for it to fit without bowing up at all. i printed it in PETG for the extra heat...
thingiverse
Hi all, I wanted to fit my new 3070 into my SG13 case, but the GPU was much longer than my 1080 Ti. After a lot of cutting and hacking, I designed an extension as well as a side vent (due to the card being fatter too) to fit the entire GPU into the...
thingiverse
PORT SPACING SKETCH INDLUDED An SFF board I had was just barely too long for the SG13, so I cut the lip down in the front and had to remove the front ports. Decided to mount it to the side of the case and it worked out. The io board bows up a little...
thingiverse
Use threaded inserts M3 x 4mm to melt them down
thingiverse
Use threaded inserts M3 x 4mm to melt them down
pinshape
The bracket is secured behind the main plate using the 4 screws of the filament compression brackets on the extruder motor and rests on the 2 NEMA motors. Mounting is OK on the extrusion head and the nozzle is compatible with the Autoleveling...
thingiverse
Give your SFX size computer powerunit a place on the printer frame. ...In my case a Silverstone ST45SF-G on a Prusa I3 (Achatz) frame
thingiverse
Supports are only for the SFX case hole. You can print other elements without supports. The base is fixed with original screws on the back, and with the fan's screws on the front. I have glued feets with Loctite, it works fine. My fans are...