shaft coupler for dc motor 3d models

Note: you need 2x 2mm (M2 2X0.45) bolts to hold the attachment in place as well as the head for the motor. Although I tested it and it worked but will update the design if I notice any flaws. Let me know what you think in the comments. Update:...

DC motor shaft coupler. ...Holds the shaft to motor using a m3x11 screw.

Model rc to wheel motor coupler. ...Can easily be edited to suite any needs. 6mm dc motor shaft.

DC motor coupler

Coupler to hold paddle pop sticks for DC motor anometer

Coupler to hold paddle pop sticks for DC motor anometer

I created a shaft coupler for a matrix leadscrew and tetrix motor. This works with neverrest motors as well. ...Just jam the leadscrew in, to get it out, smash it.

Shaft of actualsize, Scaling already done , 6mm Shaft Dia

Motor coupler for shaft from 5mm to 8mm. Strong body and 8 screws, never loose the step. Made in OpenSCAD, You can change all. Easy to print... ...O_o

Motor coupler for shaft from 5mm to 8mm. Strong body and 8 screws, never loose the step. Easy to print... O_o You can help me to do more things like this. Buy my designs at pinshape:http://pinshape.com/users/27920-jsirgado The OpenSCAD file is there,...

A device to attach a motor shaft to another shaft to allow it to drive the shaft and compensate for misalignment.

I designed this to couple a RE58 encoder flange to a motor shaft.

I designed this to couple a RE58 encoder flange to a motor shaft.

ZGA37RG DC Motor tight fit 4mm screws and nuts custom Design. ...Comment with any problems and I'll do my best to help you fix it.</p>

Motor Adapter for connecting drive screw.

This is a low cost single shaft DC geared motor. It is most suitable for light weight robot requiring small power. ...You can buy it on Banggood.com or amazon.

Coupler shaft for DC geared motor.

DC motors with accessories. ...12 volts geared motors are generally a simple DC motors.This can be used in all-terrain robots and variety of robotic applications.

Simple clamp/mounting for fixing/placing center shaft DC motor.

Simple clamp/mounting for fixing/placing center shaft DC motor. ...

This file is designed as a 10mm shaft coupler. Use M4 x 15 or M4 x 16 socket head cap screws and nuts to attach. I recommend you print this part either diagonally with the slotted side up or horizontally with the slotted side up, with supports, for...

dc gear motor side shaft

DC Geared Motor - Side shaft

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=673563 Instructions Using the following options: coupler_outside_diameter = 7.2 motor_axle_diameter = 2.3 coupler_length = 15.9 try_bigger_sizes = yes

I was making the "Simple filament extruder puller by james_III" and found some rubber wheels that had a 7mm diameter hole, but my Nema 17 motor shaft had a 5mm diameter so I needed some sort of "tube" to make the shaft fit thight on the rubber wheel...

Remix of https://www.thingiverse.com/thing:7390 by emmett ----------------------------------------------------------------------------- I wanted to see if this gearbox can be driven by a small 3-6V DC-motor. So I rebuild the sun gear for a 2mm motor...

I created a simple 8 sided shaft to use with this gearbox for servo horns or wheels or whatever you need. ...Please print in 90% Infill.

I needed to attach an impeller to RS555 motor which has a shaft length of 9mm and diameter of 3.17mm. ... This uses M3 nut and bolt to hold both propeller and shaft to the coupler. ... Design is not symmetric so the propeller nuts must face the motor.

I needed to attach an impeller to RS775 motor which has a shaft length of 8mm and diameter of 5mm. This uses M3 nut and bolt to hold both propeller and shaft to the coupler. ... Design is not symmetric so the propeller nuts must face the motor.

Motor and Auger Bit Shaft Coupler for Filament Extruder 14mm Dia Auger Bit 9mm hex socket 9mm D type Motor Shaft