shaft pulley 3d models
54158 3d models found related to shaft pulley.grabcad
This is an assembly of two shaft connected using a belt and pulley assembly, one of the shafts is also connected to another shaft using a couplingYou can see how the shaft is assembled with the pulleys, the mates allows for shafts' rotation.Project...
cgtrader
A shaft an pulley internal mechanism. ... For any queries, feel free to reach out to me- Kik: AMEYPD Telegram: AMEY_PD
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: pulley_b_ht = 8 idler_ht = 1.5 motor_shaft = 6.1 idler = 0 additional_tooth_depth = 0 retainer = 1 nut_shaft_distance = 1.2 m3_nut_flats = 5.7...
thingiverse
A pulley made for my mech's steering mechanism with a 1/4" shaft. Made for bowden wire but you probably could use other cord too. (Note, may need to reduce to 0.001 size because my software is weird like that). 0.3mm layer height and probably a...
thingiverse
Replace your piece, there are a four type of printable pulleys...
grabcad
Shaft and Pulley assembly with all required part drawings using CREO and PRO-E
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: idler = 1 no_of_nuts = 1 profile = 1 additional_tooth_depth = 1 m3_nut_depth = 2.7 pulley_t_ht = 7 retainer_ht = 3 m3_nut_hex = 1 m3_nut_flats =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: additional_tooth_depth = 0 retainer = 1 pulley_b_dia = 20 pulley_b_ht = 8 pulley_t_ht = 7 m3_nut_flats = 5.7 additional_tooth_width = 0.2 m3_dia =...
grabcad
Designing of bearings, shaft, pulley and belt drive. ...You can get solution to this problem at:https://drive.google.com/file/d/1iOZP3AbfQPdJGMfGpqJUWkfI67yLs3qm/view?usp=sharing
thingiverse
Customized version of http://www.thingiverse.com/thing:16627 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=16627
thingiverse
Customized version of https://www.thingiverse.com/thing:3544542 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3544542
thingiverse
Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627
thingiverse
Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627
thingiverse
Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627
thingiverse
Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1812136 Instructions Using the following options: belt_retainer = 1 screws_disposition = 1 nut_shaft_distance = 1.2 retainer_height = 1 base_diameter = 16 screw_profile = 4 idler_height = 1...
thingiverse
I tried to locate these replacement parts but found them extremely difficult to get hold of as they are classed as rare the only original plastic ones i could find were around £55 a set so i decided to try to make some. It was designed in 2 halves...
thingiverse
Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627
thingiverse
Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627
thingiverse
Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627