shapeoko 3d models

Shapeoko Assembly

... assembly to hold down parts for your Shapeoko. ... Use with 1/4" bolts. Instructions You can add mount points to your Shapeoko using threaded inserts, such as this. ... Print with relatively high infill density (I used 0.30) and support material.

These face-plates are for spindle speed controller and emergency stop switch - both common add ons to the Shapeoko CNC rounter Instructions I printed these on my Makerbot 2 3D printer.

An idler pulley that goes on ball bearings, roughly compatible with the ones that come with Shapeoko. Instructions I wanted to go with a dual-drive on the Y axis, but that required sourcing a second...

ShapeOko belt anchor/tensioner

Shapeoko Max CNC Absaugung

My Shapeoko probe sleeve. ...

ShapeOko Toolholder "5 Tools" Instructions ShapeOko Toolholder "5 Tools"

Dust sucker for the Z-plus Shapeoko

ShapeOko Main Toolholder can be directly connected to the case for all the tools you get with you ShapeOko Instructions ShapeOko Main Toolholder Print it and use it.

ShapeOko rubberband Penholder Instructions based on http://www.shapeoko.com/forum/viewtopic.php?f=24&t=330http://www.shapeoko.com/wiki/index.php/File:PenHolder5-2.jpg

Shapeoko 3 CNC v wheel for slider including 2 bearings.

Needed some replacement V wheels for my shapeoko 3 .

Mount the Makita RT0700C spindle to Shapeoko 2

shapeoko dust boot suits makita router simular to sweepy!

Suckit Dust boot ears for Shapeoko with HDZ.

Created this to hold the vacuum hose of the ShapeOko.

... source. http://www.shapeoko.com/ Mounting Case:http://www.shapeoko.com/wiki/index.php/Inventables_Electronics_Batch_4_and_5 Instructions ShapeOko Mounting Case for Arduinohttp://www.shapeoko.com/wiki/index.php/Inventables_Electronics_Batch_4_and_5

ShapeOko Penholders for different pensizes Penholder for Shapeoko open source CNC milling machine http://www.shapeoko.com Instructions ShapeOko Penholder Penholder for Shapeoko open source CNC milling machine adjustiable around +/-1.5mm for 10mm,...

ShapeOko Slider Penholder with sliding mechanism Instructions ShapeOko Slider Penholder similar tohttp://www.shapeoko.com/forum/viewtopic.php?f=24&t=330 you need two 3mm sticks where the holder can slide.

Shapeoko Mounte Plate Z - open source CNC milling machine see http://www.shapeoko.com/ SM-S06 Z Mount Plate Instructions Shapeoko Mounte Plate Z SM-S06 Z Mount Plate (UHMW (with bearing)http://www.shapeoko.com/wiki/index.php/Assembly_step_9 and from...

Use these to take up the gap when using limit switches on a shapeoko 2

Replacement for the standard "spindle mount" that comes with the shapeoko builder's kit.

This is to adapt a Makita RT017C to a shapeoko 1 cnc machine.

A bracket for mounting the Arduino controller on the Shapeoko y-axis motor plate

A tool offset probe to be used with a Shapeoko touch probe.

Shapeoko chain guide to push the chain back onto the top of the rails when moving,

Use these to take up the gap when using limit switches on a shapeoko 2

New version of the Shapeoko motor plate, tested at 5mm printed PLA. ...recommended cut 3mm steel.

Shapeoko 3 Electronics englosure, usefull, when working with aluminum or brass. ... Note, My shapeoko electronics are installed fliped, so the cable holes will point down when using as intended.