shark byte vtx 3d models
11736 3d models found related to shark byte vtx.
thingiverse
Custom adapter from 20x20 mounting pattern of 3" mini-quad frame to Fat Shark Shark Byte VTX 25.5x25.5 with location for antenna tubes to mount under the stack. ... Specifically designed for my XHover B-Roll.
thingiverse
Sharkbyte Whoopi board. ...Montage 20*20 Stak printing speed 5mm/s ,
thingiverse
Cut away the back to clear the crossfire immortal t mount. ... Holds it very well.
grabcad
Externally accurate model of the Sharkbyte/hdzero vtx. ...25.5x25.5mm mounting, in a single body .step for your modeling convenience.
thingiverse
Simple holdet for shar byte TX5M.1 VTX to acomodate VTX at back of the frame.
thingiverse
A 20x20 mount adapter for the Shark Byte TX5S.1 VTX.
thingiverse
This adapter requires no corner removal but is approximately 9.5mm tall which is about 3.5mm taller than the original to provide room for M3 nuts inserted in the corners after printing .Obviously bolts have to stop about 4mm in from bottom to avoid...
thingiverse
Shark Byte VTX and Camera mount for Apex 5". ... -Requires 12cm camera to VTX cable: https://www.getfpv.com/shark-byte-12cm-mipi-camera-cable-12cm.html
thingiverse
It always struck me that the keypad for adjusting the settings directly on a Shark Byte VTX is a bit vulnerable, and you don't want a loose unprotected board so close to the VTX & FC when they're powered up. So I set to and designed this folding...
thingiverse
getting stuck in the upgrade socket of the Shark Byte VTX on your quadcopter? This simple solution might be just what you're looking for. A TPU bung that grips onto the socket & keeps the pins protected from crap spraying off the props, with a...
thingiverse
### Work in progress - needs stiffening to reduce vibrations ## Pod to mount Shark Byte VTX-S on Switchback Pro Designed to allow mounting the whoop board inside the very small Switchback Pro. I also wanted to fit a large micro-sized camera/M12 lens...
thingiverse
This is a custom mount designed specifically for installing the Fat Shark Byte Frost vtx unit onto an Ummagawd Acrobrat frame. The mount was printed in PLA, which has been infused with Proto Paste carbon fiber - a material that's incredibly stiff but...
thingiverse
adapter to mount the shark byte on the fpv ev300d goggles (ev300O can be). the shark byte module is tested. ... please share photos and reviews if you do.
thingiverse
canopy to install the shark byte rx5s.1 system on a beta85x chassis (formerly 4k). ... video test image here: https://youtu.be/zFnedP03ajg
thingiverse
This is an adapter to mount FatShark Shark Byte RX5.1 receiver to FlySight Falcon goggles. It's a snap-on, no glue needed. ...You need to use a heat gun to shape the adapter.
thingiverse
Orqa FPV.One mount for Fatsharks Shark Byte. I used TheEly's Detachable Mount ( https://www.thingiverse.com/thing:4653523 ) for measurement and recreated a one-piece version with more uptilt to be used with 3M Dual Lock Velcro. I left the top...
thingiverse
Voici une un adaptateur pour les EV200D afin de vous permettre d'y fixer le VRX Shark Byte HDZERO en toutes sécurité. Les deux parties se clips entre elles et il ne reste plus qu'à visser le tout sur le vrx a la place de la plaque arrière. ...Vous...
thingiverse
For the use of byte shark on a Skyzone SKY04X. ...Print in PLA or Resin. Video Testing Shark Byte System: https://www.youtube.com/watch?v=bPWTYunsdzY
thingiverse
Mount for Shark Byte TX5M.1 VTX. Designed to give a flat base for attaching via glue or double sided tape. The nubs on the mount fit into the screws on the VTX and hold it very securely and there are cutouts on the side for cooling. weight...
thingiverse
I made an adapter board to hold the Shark Byte board on the 30mm flight stack. ... The idea is to treat the adapter as actually 'nuts' that screw down on top of the flight controller.
thingiverse
Allows mounting of a Shark Byte module to EV200D (And I think EV300D) goggles Use velcro to mount the adapter to the goggles - I stuck mine directly to the goggles, not the removable plate, because the removable plate on these goggles is awful and...
thingiverse
I missed being able to watch or share flights in the field with others using Shark Byte so cobbled this simple bracket together. Clips over any 28mm deep monitor as is...slot is 20mmx28mm and fingers are sized for stock module. ... hope this...
thingiverse
... bottom snaps. ... Shark Byte front caps replacement - for connecting custom SMA antennas. It's quite hard to print properly - bottom snaps are very fragile and thin. Printing: It was printed with 0.1mm nozzle PETG very long print. ...
thingiverse
You know that little keypad that comes with your Shark Byte system? That little fragile thing that is mandatory for setting the system up if your UART connection is not working right? That thing that is not cheap to replace if you damage or loose it?...
thingiverse
Shark Byte VRX Tile angled I mangled Adninco's vrx tile to provide a little more room underneath for the ufl-sma connector and to angle them out some.Added lettering to 2 and left 1 blank..fits well thanks to Adninco's hard work.. printed in pla...