shark vacuum attachments 3d models

Shark Vacuum Cleaner Attachment Stand The hole sizes are 41.00mm so measure your Shark attachment diameter to check they'll fit (mine are 39.5MM) made them a little larger to make sure they fit. The motorized Pet tool fits a little tighter but is...

The bracket that came with my Shark vacuum cleaner could only hold one of the two attachments that came with the vacuum. ...This allows storage for both attachments!

... ...The manufacturer gives you 3 attachments with the vacuum and only two spots to attach them to it. This fits onto the lower left attachment holder. It clips in place with no glue or screws and holds the red lint remover attachment firmly in place.

I was disappointed that my Shark Vacuum cleaner didn't have an attachment holder. Tapered top to allow the tool to easily fit on and off the holder. Printed in PLA to allow the holder to flex and snap round the wand tube. ... Fits my IC160UKT,...

Use this holder to attach Shark's standard duster crevice tool to the wand on a Shark stick vacuum. It's specifically designed for the P50 vacuum, but there's a good chance it'll work on other Shark stick vacs.The holder clips on to the extension...

Use this holder to attach Shark's standard duster crevice tool to the wand on a Shark stick vacuum. It's specifically designed for the P50 vacuum, but [RaceReadyJ](https://www.thingiverse.com/make:616430) got it to fit onto the AX952. So, there's a...

This is a set of attachments I made for my Shark Rocket Corded (HV302) vacuum cleaner. I added 4 vent holes since necking down the vacuum causes it to struggle. These help to relieve some of the strain on the vacuum whilst still providing plenty of...

Remixed from [Thingiverse](https://www.thingiverse.com/thing:4567459) to hold other Shark hose attachments. If you don't mind the print being a tad flimsy, set your slicer to only print the first few layers. My first prototype print was only 4...

This is a rack for the two attachments that come with the Shark Rocket vacuum. ...It can be printed with no supports if printed bottom down.

Tested on my Shark Stick vacuum and works perfectly. Credit for original design goes to user "rpwong", as all I did was modify his STL file and thicken up the walls. Recommended to print with some decent infill, roughly 70-80%. ...Printed mine...

I made these attachments for my Shark Vertex Pro but should fit any vacuum with a 34mm attachment wand. I printed with PLA and it's held up pretty well. ...I printed them vertically, the bottom facing down and with supports.

Allows use of small, standard attachments with the Shark SV75_N or similar portable vacuum cleaner.

A simple adapter I drew up so I could use my shark hardwood attachment on my dyson stick vacuum. ... The dyson interface is perfect, but I might need to update the shark end since it is a friction fit and currently might be too loose.

A simple adapter I drew up so I could use my shark hardwood attachment on my dyson stick vacuum. ... The dyson interface is perfect, but I might need to update the shark end since it is a friction fit and currently might be too loose.

It doesn't come with any way to carry around attachments other than a little bag. Wifey wanted something to clip on her most used one, the crevice tool. Seems to work so far. I put together with 2 10-20x3/4" machine screws, washers, and nuts I...

... tool. Seems to work so far.</p><p>I put together with 2 10-20x3/4" machine screws, washers, and nuts I had on hand.</p><p>Printed PLA+ at .2 with 5% infill. You might have to bump up the infill a little or just modify near the prong attachment area.

I got tired of not having anywhere for the attachments so made this. Needs quite abit of infill, I use minimum of 3 outer layers. ... I sell these in my own eBay shop, you are welcome to take it, remix it etc but please don't just print and sell my...

I got tired of not having anywhere for the attachments so made this. ...Needs quite abit of infill, I use minimum of 3 outer layers.</p> <p>I sell these in my own eBay shop, you are welcome to take it, remix it etc but please don't just print and sell...

An attachment holder for the Shark Lift Away vacuum cleaner. I know for sure that this will work with the NV356 model, but it may also work for other Shark models that have a similar design. Remove the vacuum cleaner handle and simply slide it on.

Attachment holder for a Shark Vacuum model ZU560 allowing two instead of the default one. Printing: I used three walls, gyro infill, and PETG. I included my settings for PrusaSlicer. CAD: The CAD file is for the under appreciated DesignSpark...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4ftNd1lxN2M

I modified the inner diameter of the connection to allow for use with Shark vacuums

<p>I printed this with the small side down to avoid a small internal overhang. ...It fits snugly on both the vacuum cleaner and the attachment.

I had a Shark Rocket handheld vacuum that I didnt care for. Later I bought a Dyson V7 cordless hand held vacuum which I like much better. But the Dyson brush attachment is not very ergonomic. This adapter has a release button to hold it in the...

Replacement for the vacuum hose attachment for a Shark Navigator Lift-Away Professional, model UV540 26. May work on other models in the series, but I only know it works for sure on this one. Just a quick mock-up with Fusion 360. The only real...

For storing extra Shark vacuum attachments.&nbsp;Includes the Fusion360 file for customizing.

This is a wall mount for Shark vacuum cleaner attachments and accessories. ...It is attached to a wall using a few strips of double sided tape.

My wife wanted an adapter for her Shark vacuum to attach a 7/8" OD flexible hose to clean out the dryer. So I drew this up and went to the local hardware store and bought 2' of the 5/8" id clear reinforced hose. She's happy, so guess what, I'm not...

Shark Anti Hair Wrap Cordless Stick Vacuum Cleaner IZ201UKTSB attachments holder 2x 30mm m5 bolts needed The 2 side holes fit the heavier accessories snuggly . ...The one at the back is for the lighter nozzle.

Includes a variety of attachments that can be used for a vacuum hose. &nbsp;These attachments slide on and off the hose with ease. &nbsp;I personally use these with my Ryobi handheld vacuum and my Hoover floor vacuum. &nbsp;Feel free to print what...