sharkbite 3d models

This is depth gauge for sharkbite 1/2

Releasing SharkBite couplings just got a whole lot easier with this clever little tool! Simply grasp the removal tool firmly and position it precisely over the target key. With a smooth, gentle motion, press down on the tool until it engages with the...

The company's standard version is too small to get adequate amount of pressure to force the SharkBite fitting to release from the pipe. This is a 2-part style that interlocks to give you full 360 coverage and a much large diameter to apply pressure...

Customized version of https://www.thingiverse.com/thing:1943463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1943463

Customized version of https://www.thingiverse.com/thing:1943463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1943463

This is a basic depth gauge for a 3/4 inch Sharkbite fitting. Handy for ensuring the pipe is inserted far enough into the fitting for a leak-free connection. ...The pipe insertion depth is 29 mm (1.13 inches).

This is a basic depth gauge for a 3/4 inch Sharkbite fitting. Handy for ensuring the pipe is inserted far enough into the fitting for a leak-free connection. ...The pipe insertion depth is 29 mm (1.13 inches).

I'm remixing the Sharkbite base, but this time I've added extra support at the top. ...Unfortunately, two prints were damaged during testing due to excessive pressure on the upper section.

... It accommodates 1" SharkBite PEX tubing and 1/2" EMT pipes. The design utilizes a 1/4" x 2" bolt with nut and washer to secure the EMT to the base. ...Two #8 x 1/2" sheet metal screws or similar are used to fasten the PEX into the base securely.

This is a removal clip for SharkBite fittings designed with functionality in mind. A standard clip may not provide enough grip, leading to difficulty handling the device. I developed an enhanced model that includes flanges allowing you to firmly...

These adapters are designed to fit on top of PEX tubing commonly sold under the brand SharkBite. They're available at many hardware stores including Home Depot. They hold the base only of a PixaBulb (remove clear lens). Here's an overview:...

Customized version of https://www.thingiverse.com/thing:1943463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1943463

Customized version of https://www.thingiverse.com/thing:1943463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1943463

Customized version of https://www.thingiverse.com/thing:1943463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1943463

Customized version of https://www.thingiverse.com/thing:1943463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1943463

<p>Small picture frame that looks like a shark or monster took a bite. ...Meant to be used a desk ornament or hung using adhesive strips.&nbsp;</p><p>&nbsp;</p><p><i>Unscaled size is 3 inches by 4 inches</i></p>

Remake with dual pipe holder. Center countersunk screw down, and tie wrap opening mid point. Used if for IN-OUT connection for solar pool heater. ... Cheers

Customized version of https://www.thingiverse.com/thing:1943463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1943463

I remixed swholmstead's fantastic removal tool by adding/changing the following: 1) Added ergonomic thumb/finger holds 2) Making it less deep so it can fit in tighter spaces (ie between sharkbite and an elbow) 3) Added a thin lip on the inner (top)...

I required a removal tool to extract the Sharkbite fittings from my water heater, but mine was nowhere to be found. Frustrated, I visited my local hardware store, only to discover they were completely sold out. In a pinch, I decided to fabricate one...

SharkBite U702, Safe Seal Depth and Pipe Deburring ToolUsed to deburr copper and CPVC pipes for plumbing.Also the depth portion of the tool can be used to figure out how much length of pipe you need to install quick connect style copper or CPVC pipe...

SharkBite U702, Safe Seal Depth and Pipe Deburring ToolUsed to deburr copper and CPVC pipes for plumbing.Also the depth portion of the tool can be used to figure out how much length of pipe you need to install quick connect style copper or CPVC pipe...

This is a 2-piece clamp for making Tiny Whoop gates with sharkbite or similar 16mm OD tubing featuring LEDs inside. Print two identical halves and bolt them together using M4x20 hardware. This clamp is designed for approximately 16" gates,...

decided I would try and make my own SharkBite measurement and deburring tool since I didn't want to spend over $20 to buy the commercial one.This is for 1/2" tubing and allows you to mark the 24mm depth for 1/2" sharkbite fittings and includes a...

This is a 2-piece clamp for making Tiny Whoop gates using sharkbite (or similar) 16mm OD tubing with LEDs inside! Print 2 identical halves and bolt together with M4x20 hardware. It is sized for a approx 16" gate (1200mm tubing/LED strip) but you...

I was working on a project that required a removal tool but didn't feel like driving to the store to buy one. So, I decided to make my own for each size needed. These tools work perfectly with copper pipe and have been put to the test. I haven't...

Transformed to perfection with cutting-edge 3D Slash technology.

Revolutionized by innovative technology, this cutting-edge human model is fully customized with advanced 3D capabilities using the powerful platform of 3D Slash!

These are TPU Parts if you would like to experiment with running HD FPV System on a JS-1. Please note these were never intended as final parts but rather allow us to compare both the DJI system to the FatShark. The DJI Pod was designed first...

Crafted with precision using the innovative platform of 3D Slash.