shelf for windowsill 3d models

......I designed this to fit the standard 1/64th scale Hot Wheels diecast cars but it can be used for anything else. ...The recessed top surface prevents the cars from rolling or sliding off the edge. Prints without supports and with low infill percentage.

Top surface is 150x150mm. The cable pass through is 15mm in diameter. The shelf is 80mm high (the part that mounts to the wall).The screw holes are for M3.5 countersunk screws. 

The monitor riser I was given at my workplace was a bit too high for my monitor, so I decided to get the cheapest Ikea Burhult shelf (the cheapest I found) and make some adapters that insert into the shelf by pressure, no screws needed. I wanted...

Cover for shelf to wrap around tubing of dust extractorThis is a set of covers for the break through of the tubing of dust extractor in a kitchen cabinet shelf. (Extractor is Ikea Utdrag). The wall cabinet on the picture is an Ikea Metod 60x60 (x...

... The supports stand 5.875 inches tall from the bottom of the unit to the underside of the first shelf, including a foam bottom pad for added stability. From the top of the bottom shelf to the underside of the top shelf, they are 4.125 inches tall.

I used self drilling sheet metal screws.Angle IronFor the shelf supports you need an angle iron.The 80 mm side is used to support the Jobox system. The 120mm side defines how high you can adjust the angle iron. Could be bigger or smaller in some...

Hello nerds, today I bring you this design that in the first instance I would only use it for a clock that I have for my improvised office, however the dimensions of the area are ideal for funkos, so you can use it as a support for funko type shelf,...

For kichen

This design is intended for a simple shelf made from a wooden plank attached to a wire rack. The plank, sourced from Daiso, measures 100mm in length, 35mm in width, and 9mm in thickness. This project is not meant for commercial use or distribution;...

Shelf that mounts to the Peloton handlebar post and holds the case for the Beats Fit Pro. Using https://www.thingiverse.com/thing:5179759 for the form and https://www.thingiverse.com/thing:5699116 for the post profile. Install using the existing...

Under shelf mount for Dopper bottles. Stuck mine with some double sided tape. The bottles are pretty light when empty so the weight is no problem. I also included screw holes just in case. I included mounts for 1, 2, or 3 bottles. The openscad file...

 The screws that you will need to use should be about 15 mm in length.Place the screw in the T-nut through the holes in the LEGO shelf and screw it in until the T-nut is about 2-3 mm from the back of the LEGO shelf, insert the T-nuts vertically...

Petite étagère pour Ikea Skadis pour le modèle de Bugman_140 Dry Dock pour le fameux Benchy.Impression facile en 0,2mm en PLA ou autre, avec un remplissage de 10%, avec supports.-------Small shelf for Ikea Skadis for Bugman_140 Dry Dock for the...

I've designated a specific area for all printer-supplied tools, as well as a spot for small loose items and the 3D Print Removal Tool, which I utilize – The Raft Ninja being my go-to tool. To secure this shelf to the wall, I rely on Scotch Indoor...

There are two versions available: one designed specifically for use with double-sided tape and another that uses screws for secure attachment. ... Additionally, I've added a third option, an STL file with a 1-inch / 26mm width, which perfectly matches...

I need only one ikea billy board for my shelf. So why not print in PLA Wood? This should fit 100% alls measurements were taken from the original one. I added a pre sliced file for my XL. I needed to cut 1,5mm on each side to make it Fit, but this is...

Modular storage shelf for hanging in wardrobe by means of an adapted hanger, perfect for organizing small garments in boxes stacked one on top of the other. By downloading this file, you agree NOT to sell or redistribute this product. This design is...

Hi, this is a bed-side phone shelf nothing else, enjoy

Small pen and screwdriver holder built to slide neatly under a shelf.

This is a shelf clip with a hook, that you can slide over a standard 18mm shelf or plank. ... I'm using it to hang a coat hanger to a shelf in the laundry / storage room, which has shelfs made out of standard 18mm thick board. ...

Hi, this is a bed-side phone shelf nothing else, enjoy

The hanger easily slides over the bottom shelf, and lets the headphones hang.

required parts: 2x 4mm perspex/Plexiglas pane (for doors; choose dimensions to fit your shelf and leave 1-3 mm tolerance in each direction) 4x wooden bars - length to fit your shelf, width 100 mm, thickness 16-20mm 8x M3x10 screw 8x M3 Hex nut up to...

PRODUCT DESCRIPTION Elevate your VR, AR and game environments with a precision-crafted shelf for books. Made for optimal performance in Virtual Reality, Augmented Reality and real-time applications, this detailed model comes pre-textured for the PBR...

Sadly, the shelf creator didn't allow for remixes of the design, so I'll link them both instead, as this is designed to fit the system. It was really important to my players that this store sold books, so I wanted to make sure that I had some models...

Clip-on keyhooks for Target's Threshold™ Shelf Floor Lamp (https://www.target.com/p/shelf-floor-lamp-brown-includes-energy-efficient-light-bulb-threshold-153/-/A-15426014) The hooks slip and snap onto the plastic lip right under the cloth shade. The...

This is an adapter designed to utilize a standard 8"x10" shelf bracket from the hardware store to provide center support for shelving systems in Keter brand sheds without drilling into the plastic shed. The brackets I tested with are labeled as...

Its intended purpose is to be attached securely to the bottom of the parcel shelf, serving as a stable base for mounting. To ensure optimal performance, I printed mine using ABS material. Prior to application, thoroughly prepare the surface of the...

... to be installed, either friction-fitted or glued, after the holder has been attached to the wall. ...The semi-circular cutout is room for the screw's head.I would advise printing it standing up, with supports for the screw hole, to limit warping.

... itself. ...You should print one "top" and at least one "mid", though I used 2. The mid section should be screwed in - I used the screws provided for the wall mount for the Billy shelf. ...Fusion360 design files attached Category: Organization